m1-z50 Spur Gear, Spur gear

STEP · STL Supports CommunityCAD0 downloads
m1-z50 Spur Gear, Spur gear
1 / 7

m1-z50 Spur Gear, Spur gear

The m1-z50 spur gear: reference (pitch) diameter 50 mm, tip (outside) diameter 52 mm, root diameter 47.5 mm. Available as simplified STEP files.

m1-z50 spur gear, Spur gear

This model is CommunityCAD's own, drawn from KHK's published drawing; KHK did not make or endorse it.

How these parts are made, and what the levels mean: read the method

  • Also known as: m1-z50 metric spur gear, m1-z50 involute gear, m1-z50 straight cut gear, m1-z50 pinion
  • Model id: spur-gears-m1-z50
  • Standard: Spur gear · size m1-z50

Files

Part keySimplified
spur-gears-m1-z50STEP

Dimensions

Dimension symbols for m1-z50 spur gears (Spur gear)

SymbolNameminnommaxModeledRuleLevel
dReference (pitch) diameter5050nominalL2
daTip (outside) diameter5252nominalL2
dfRoot diameter47.547.5nominalL0 (nom: one source)
dsBore diameter1010nominalL2
dhHub diameter3535nominalL2
bFace width1010nominalL2
lhHub width1010nominalL2
dh_hpcHPC's hub (boss) diameter3030nominalL0 (nom: one source)
ds_hpcHPC's bore1010nominalL0 (nom: one source)
LTotal length2020nominalL2

Drawing

Drawing of the m1-z50 spur gear with its values (Spur gear)

As a PDF: CC-SPUR-SZ-m1-z50.pdf.

The m1-z50 spur gear beside the m1-z40 and the m1-z60

The m1-z50 is number 17 of the 32 Spur gears published here, listed from m0.5-z15 to m2-z60.

  • Reference (pitch) diameter (d): 50 mm on the m1-z50 spur gear, against 40 mm on the m1-z40 and 60 mm on the m1-z60.
  • Tip (outside) diameter (da): 52 mm on the m1-z50 spur gear, against 42 mm on the m1-z40 and 62 mm on the m1-z60.
  • Root diameter (df): 47.5 mm on the m1-z50 spur gear, against 37.5 mm on the m1-z40 and 57.5 mm on the m1-z60.
  • Bore diameter (ds): 10 mm on the m1-z50 spur gear, the same on the m1-z40 and the m1-z60.
  • Hub diameter (dh): 35 mm on the m1-z50 spur gear, the same on the m1-z40 and the m1-z60.
  • Face width (b): 10 mm on the m1-z50 spur gear, the same on the m1-z40 and the m1-z60.
  • Hub width (lh): 10 mm on the m1-z50 spur gear, the same on the m1-z40 and the m1-z60.
  • HPC's hub (boss) diameter (dh_hpc): 30 mm on the m1-z50 spur gear, against 20 mm on the m1-z40 and 30 mm on the m1-z60.

Other sizes

Conventions

  • One level: one steel solid with true involute teeth. STEP AP214, millimetres, the bore on Z, the toothed band's plain face at z = 0, the hub toward +Z, a tooth centred on +X.
  • Nominal teeth: the tooth as thick as the space on the reference circle (pi m / 2), no backlash allowance; real gears are cut slightly thinner for backlash.
  • Plain bore only: KHK's tapped (set screw) and keyway variants are not modeled.

Documents

Sources

hpc-steel-spur-gears, khk-ss-spur-gears, misumi-eu-gears. Full citations: the method page and this size's datasheet.

Found an error? Use the feedback section on this page.

Comments

Sign in to leave a comment.

Loading comments...

From the datasheet

docs/CC-SPUR-DS-m1-z50.pdf

'?) CommunityCAD CC-SPUR-DS-m1-z50 revA Size datasheet - m1-z50 Module 1, 50 teeth, spur gear Size datasheet: this size's values with their levels, conventions and sources. m1-z50, end, 0.5:1 For meshing with other module 1 Pott gears on a parallel shaft Part key spur-gears-m1-z50 m1-z50, side…

View full datasheet →

docs/CC-SPUR-SZ-m1-z50.pdf

Involute spur gear, ISO 53 basic rack, m1-z50 Size drawing - m1-z50 values on the views - enlarged 2:1 Reference (pitch) diameter @d = 50.00 Tip (outside) diameter Root diameter Bore diameter (KHK, L2) Hub diameter (KHK, L2) Face width (KHK, L2) Hub width (KHK, L2) Total length (KHK, L2) HPC boss…

View full datasheet →