8x11 Sintered Bronze Bushing, ISO 2795

STL Supports CommunityCAD0 downloads
8x11 Sintered Bronze Bushing, ISO 2795
1 / 7

8x11 Sintered Bronze Bushing, ISO 2795

For an 8 mm shaft in an 11 mm housing bore, this 8x11 sintered bronze bushing (ISO 2795) presses in and runs on the oil in its sintered wall. Modeled as 3 lengths from 6 to 12 mm, each as simplified STEP.

8x11 × 8 sintered bronze bushing, ISO 2795

How these parts are made, and what the levels mean: read the method

  • Also known as: 8x11 oilite bushing, 8x11 sleeve bearing, 8x11 plain bearing, 8x11 self-lubricating bush, 8x11 x 6 to 8x11 x 12
  • Model id: iso2795-c-8x11
  • Standard: ISO 2795:2020 · size 8x11

Lengths

Length (mm)Part keySimplified
6iso2795-c-8x11x6STEP
8iso2795-c-8x11x8STEP
12iso2795-c-8x11x12STEP

Dimensions

Dimension symbols for 8x11 sintered bronze bushings (ISO 2795)

SymbolNameminnommaxModeledRuleLevel
dInside diameter88nominalL2
DOutside diameter1111nominalL2
CChamfer, maximum0.30.3single limit (max), modeled at the limitL2
C_angleChamfer angle4545nominalL1

Drawing

Drawing of the 8x11 sintered bronze bushing with its values (ISO 2795)

As a PDF: CC-ISO2795-SZ-8x11.pdf.

The 8x11 sintered bronze bushing beside the 8x12 and the 9x14

The 8x11 is number 14 of the 20 ISO 2795 sintered bronze bushings published here, listed from 2x5 to 12x16.

  • Inside diameter (d): 8 mm on the 8x11 sintered bronze bushing, against 8 mm on the 8x12 and 9 mm on the 9x14.
  • Outside diameter (D): 11 mm on the 8x11 sintered bronze bushing, against 12 mm on the 8x12 and 14 mm on the 9x14.
  • Chamfer, maximum (C): up to 0.3 mm on the 8x11 sintered bronze bushing, against up to 0.3 mm on the 8x12 and up to 0.4 mm on the 9x14.
  • Chamfer angle (C_angle): 45° on the 8x11 sintered bronze bushing, the same on the 8x12 and the 9x14.

Other sizes

Conventions

  • Simplified only: a bush has no thread, so there is one detail level. STEP AP214, millimetres, Z the axis, one end face at Z = 0 and the other at Z = L.
  • Nominal sizes: the sources give tolerance classes, not limits (before fitting G7/G8 bore, s7/s8 outside, js13 length; H7 or H8 bore after press-fitting), so the model is the nominal part before fitting, concentric.
  • A chamfer C, at C_angle from the axis, on the bore and outside edges at both ends: Table 2's maximum for the wall (D - d)/2, modeled at the limit, within the owner's quarter-wall cap.

Documents

Sources

bowman-iso2795-plain, iso2795-2020-sample, iso2795-2020-sample-figures, selfoil-iso2795-plain. Full citations: the method page and this size's datasheet.

Found an error? Use the feedback section on this page.

Comments

Sign in to leave a comment.

Loading comments...

From the datasheet

docs/CC-ISO2795-DS-8x11.pdf

* CC-1S02795-DS-8x11 revA '?) CommunityCAD Size datasheet - 8x11 ISO 2795 8x11 sintered bronze bush Size datasheet: this bush's values with their levels, conventions and sources. For 8 mm shafts ina 11 mm housing bore Part key iso2795-c-8x11x<L> Files 3 STEP AP214 (simplified), one per length…

View full datasheet →

docs/CC-ISO2795-SZ-8x11.pdf

ISO 2795 sintered bronze bush, cylindrical, 8x11 Size drawing - 8x11 values on the views - L = 8 shown; lengths 6, 8, 12 - enlarged 5:1 8x11 Source levels Main value = the modeled value (nominal, else the middle of min-max). Grey under a value = its min-max, where the source gives both. < / = =…

View full datasheet →