12x16 Sintered Bronze Bushing, ISO 2795

STL Supports CommunityCAD0 downloads
12x16 Sintered Bronze Bushing, ISO 2795
1 / 7

12x16 Sintered Bronze Bushing, ISO 2795

For a 12 mm shaft in a 16 mm housing bore, this 12x16 sintered bronze bushing (ISO 2795) presses in and runs on the oil in its sintered wall. Modeled as 3 lengths from 8 to 20 mm, each as simplified STEP.

12x16 × 12 sintered bronze bushing, ISO 2795

How these parts are made, and what the levels mean: read the method

  • Also known as: 12x16 oilite bushing, 12x16 sleeve bearing, 12x16 plain bearing, 12x16 self-lubricating bush, 12x16 x 8 to 12x16 x 20
  • Model id: iso2795-c-12x16
  • Standard: ISO 2795:2020 · size 12x16

Lengths

Length (mm)Part keySimplified
8iso2795-c-12x16x8STEP
12iso2795-c-12x16x12STEP
20iso2795-c-12x16x20STEP

Dimensions

Dimension symbols for 12x16 sintered bronze bushings (ISO 2795)

SymbolNameminnommaxModeledRuleLevel
dInside diameter1212nominalL2
DOutside diameter1616nominalL2
CChamfer, maximum0.30.3single limit (max), modeled at the limitL2
C_angleChamfer angle4545nominalL1

Drawing

Drawing of the 12x16 sintered bronze bushing with its values (ISO 2795)

As a PDF: CC-ISO2795-SZ-12x16.pdf.

The 12x16 sintered bronze bushing beside the 12x18

The 12x16 is the last of the 20 ISO 2795 sintered bronze bushings published here, listed from 2x5 to 12x16.

  • Inside diameter (d): 12 mm on the 12x16 sintered bronze bushing, the same on the 12x18.
  • Outside diameter (D): 16 mm on the 12x16 sintered bronze bushing, against 18 mm on the 12x18.
  • Chamfer, maximum (C): up to 0.3 mm on the 12x16 sintered bronze bushing, against up to 0.4 mm on the 12x18.
  • Chamfer angle (C_angle): 45° on the 12x16 sintered bronze bushing, the same on the 12x18.

Other sizes

Conventions

  • Simplified only: a bush has no thread, so there is one detail level. STEP AP214, millimetres, Z the axis, one end face at Z = 0 and the other at Z = L.
  • Nominal sizes: the sources give tolerance classes, not limits (before fitting G7/G8 bore, s7/s8 outside, js13 length; H7 or H8 bore after press-fitting), so the model is the nominal part before fitting, concentric.
  • A chamfer C, at C_angle from the axis, on the bore and outside edges at both ends: Table 2's maximum for the wall (D - d)/2, modeled at the limit, within the owner's quarter-wall cap.

Documents

Sources

bowman-iso2795-plain, iso2795-2020-sample, iso2795-2020-sample-figures, selfoil-iso2795-plain. Full citations: the method page and this size's datasheet.

Found an error? Use the feedback section on this page.

Comments

Sign in to leave a comment.

Loading comments...

From the datasheet

docs/CC-ISO2795-DS-12x16.pdf

* CC-1S802795-DS-12x16 revA '?) CommunityCAD Size datasheet - 12x16 ISO 2795 12x16 sintered bronze bush Size datasheet: this bush's values with their levels, conventions and sources. For 12 mm shafts ina 16 mm housing bore Part key iso2795-c-12x16x<L> Files 3 STEP AP214 (simplified), one per…

View full datasheet →

docs/CC-ISO2795-SZ-12x16.pdf

ISO 2795 sintered bronze bush, cylindrical, 12x16 Size drawing - 12x16 values on the views - L = 12 shown; lengths 8, 12, 20 - enlarged 5:1 12x16 Source levels Main value = the modeled value (nominal, else the middle of min-max). Grey under a value = its min-max, where the source gives both. < / =…

View full datasheet →