10x14 Sintered Bronze Bushing, ISO 2795

STL Supports CommunityCAD0 downloads
10x14 Sintered Bronze Bushing, ISO 2795
1 / 7

10x14 Sintered Bronze Bushing, ISO 2795

Pressed into a 14 mm housing bore, the 10x14 sintered bronze bushing (ISO 2795) carries a 10 mm shaft on its oil-filled wall. It comes in 3 lengths from 8 to 16 mm, each as simplified STEP.

10x14 × 10 sintered bronze bushing, ISO 2795

How these parts are made, and what the levels mean: read the method

  • Also known as: 10x14 oilite bushing, 10x14 sleeve bearing, 10x14 plain bearing, 10x14 self-lubricating bush, 10x14 x 8 to 10x14 x 16
  • Model id: iso2795-c-10x14
  • Standard: ISO 2795:2020 · size 10x14

Lengths

Length (mm)Part keySimplified
8iso2795-c-10x14x8STEP
10iso2795-c-10x14x10STEP
16iso2795-c-10x14x16STEP

Dimensions

Dimension symbols for 10x14 sintered bronze bushings (ISO 2795)

SymbolNameminnommaxModeledRuleLevel
dInside diameter1010nominalL2
DOutside diameter1414nominalL2
CChamfer, maximum0.30.3single limit (max), modeled at the limitL2
C_angleChamfer angle4545nominalL1

Drawing

Drawing of the 10x14 sintered bronze bushing with its values (ISO 2795)

As a PDF: CC-ISO2795-SZ-10x14.pdf.

The 10x14 sintered bronze bushing beside the 10x16 and the 12x18

The 10x14 is number 18 of the 20 ISO 2795 sintered bronze bushings published here, listed from 2x5 to 12x16.

  • Inside diameter (d): 10 mm on the 10x14 sintered bronze bushing, against 10 mm on the 10x16 and 12 mm on the 12x18.
  • Outside diameter (D): 14 mm on the 10x14 sintered bronze bushing, against 16 mm on the 10x16 and 18 mm on the 12x18.
  • Chamfer, maximum (C): up to 0.3 mm on the 10x14 sintered bronze bushing, against up to 0.4 mm on the 10x16 and up to 0.4 mm on the 12x18.
  • Chamfer angle (C_angle): 45° on the 10x14 sintered bronze bushing, the same on the 10x16 and the 12x18.

Other sizes

Conventions

  • Simplified only: a bush has no thread, so there is one detail level. STEP AP214, millimetres, Z the axis, one end face at Z = 0 and the other at Z = L.
  • Nominal sizes: the sources give tolerance classes, not limits (before fitting G7/G8 bore, s7/s8 outside, js13 length; H7 or H8 bore after press-fitting), so the model is the nominal part before fitting, concentric.
  • A chamfer C, at C_angle from the axis, on the bore and outside edges at both ends: Table 2's maximum for the wall (D - d)/2, modeled at the limit, within the owner's quarter-wall cap.

Documents

Sources

bowman-iso2795-plain, iso2795-2020-sample, iso2795-2020-sample-figures, selfoil-iso2795-plain. Full citations: the method page and this size's datasheet.

Found an error? Use the feedback section on this page.

Comments

Sign in to leave a comment.

Loading comments...

From the datasheet

docs/CC-ISO2795-DS-10x14.pdf

* CC-1S02795-DS-10x14 revA '?) CommunityCAD Size datasheet - 10x14 ISO 2795 10x14 sintered bronze bush Size datasheet: this bush's values with their levels, conventions and sources. For 10 mm shafts ina 14 mm housing bore Part key iso2795-c-10x14x<L> Files 3 STEP AP214 (simplified), one per length…

View full datasheet →

docs/CC-ISO2795-SZ-10x14.pdf

ISO 2795 sintered bronze bush, cylindrical, 10x14 Size drawing - 10x14 values on the views - L = 10 shown; lengths 8, 10, 16 - enlarged 5:1 10x14 Source levels Main value = the modeled value (nominal, else the middle of min-max). Grey under a value = its min-max, where the source gives both. < / =…

View full datasheet →