8x42 Stepper Motor, NEMA ICS 16
42 mm long behind an up to 20.3 mm square face, the 8x42 stepper motor (NEMA ICS 16) mounts by four M2 holes 16 mm apart around a 16 mm pilot; its shaft is 4 mm across, 10 mm long, flatted to 3.5 mm. Here as simplified STEP files.

How these parts are made, and what the levels mean: read the method
- Also known as: 8x42 NEMA stepper, 8x42 hybrid stepper motor, 8x42 stepping motor
- Model id:
nema-steppers-8x42
- Standard: NEMA ICS 16 · size 8x42
Files
| Part key | Simplified |
|---|
nema-steppers-8x42 | STEP |
Dimensions

| Symbol | Name | min | nom | max | Modeled | Rule | Level |
|---|
| L | Body length | | 42 | | 42 | nominal | L0 (nom: one source) |
| BD | Body square | | | 20.3 | 20.3 | single limit (max), modeled at the limit | L1 |
| A | Mounting hole spacing | | 16 | | 16 | nominal | L1 |
| nh | Number of mounting holes | | 4 | | 4 | nominal | L1 |
| dt | Mounting hole thread | | 2 | | 2 | nominal | L1 |
| N | Pilot diameter | | 16 | | 16 | nominal | L1 |
| T | Pilot height | | 1.5 | | 1.5 | nominal | L1 |
| D | Shaft diameter | | 4 | | 4 | nominal | L1 |
| E | Shaft length | | 10 | | 10 | nominal | L1 |
| F | Shaft flat | | 3.5 | | 3.5 | nominal | L0 (nom: one source) |
| Lf | Flat length | | 7 | | 7 | nominal | L0 (nom: one source) |
Drawing

As a PDF: CC-NEMA-SZ-8x42.pdf.
What each maker states
- Mounting hole spacing A: makers range from 15.4 to 16 mm (Leadshine 15.4 mm, MOONS' 16 mm). The model uses the largest stated, 16 mm, so check your own motor's drawing before drilling a plate for it.
The 8x42 stepper motor beside the 8x30 and the 8x48
The 8x42 is number 2 of the 19 NEMA ICS 16 stepper motors published here, listed from 8x30 to 34x118.
- Body length (L): 42 mm on the 8x42 stepper motor, against 30 mm on the 8x30 and 48 mm on the 8x48.
- Body square (BD): up to 20.3 mm on the 8x42 stepper motor, the same on the 8x30 and the 8x48.
- Mounting hole spacing (A): 16 mm on the 8x42 stepper motor, the same on the 8x30 and the 8x48.
- Number of mounting holes (nh): 4 on the 8x42 stepper motor, the same on the 8x30 and the 8x48.
- Mounting hole thread (dt): 2 mm on the 8x42 stepper motor, the same on the 8x30 and the 8x48.
- Pilot diameter (N): 16 mm on the 8x42 stepper motor, the same on the 8x30 and the 8x48.
- Pilot height (T): 1.5 mm on the 8x42 stepper motor, the same on the 8x30 and the 8x48.
- Shaft diameter (D): 4 mm on the 8x42 stepper motor, the same on the 8x30 and the 8x48.
Other sizes
- One size smaller: 8x30 Stepper Motor, NEMA ICS 16, NEMA 8, up to 20.3 mm square, 30 mm long, 4 mm shaft, M2 mounting holes 16 mm apart, Anaheim Automation, Leadshine and MOONS' data.
- One size larger: 8x48 Stepper Motor, NEMA ICS 16, NEMA 8, up to 20.3 mm square, 48 mm long, 4 mm shaft, M2 mounting holes 16 mm apart, Anaheim Automation, Leadshine and MOONS' data.
Conventions
- STEP AP214, millimetres, the mounting face at Z = 0 centred on the shaft's axis, the shaft along +Z.
Documents
Sources
anaheim-08y, leadshine-cm-steppers, moons-hybrid-steppers-figures, rule-nema-steppers-length. Full citations: the method page and this size's datasheet.
Found an error? Use the feedback section on this page.
Comments
Sign in to leave a comment.
Loading comments...