8x48 Stepper Motor, NEMA ICS 16
NEMA 8, 48 mm body: the 8x48 stepper motor (NEMA ICS 16) has four M2 holes 16 mm apart, a 16 mm pilot and a 4 mm shaft. Download it as simplified STEP files.

How these parts are made, and what the levels mean: read the method
- Also known as: 8x48 NEMA stepper, 8x48 hybrid stepper motor, 8x48 stepping motor
- Model id:
nema-steppers-8x48
- Standard: NEMA ICS 16 · size 8x48
Files
| Part key | Simplified |
|---|
nema-steppers-8x48 | STEP |
Dimensions

| Symbol | Name | min | nom | max | Modeled | Rule | Level |
|---|
| L | Body length | | 48 | | 48 | nominal | L0 (nom: one source) |
| BD | Body square | | | 20.3 | 20.3 | single limit (max), modeled at the limit | L1 |
| A | Mounting hole spacing | | 16 | | 16 | nominal | L1 |
| nh | Number of mounting holes | | 4 | | 4 | nominal | L1 |
| dt | Mounting hole thread | | 2 | | 2 | nominal | L1 |
| N | Pilot diameter | | 16 | | 16 | nominal | L1 |
| T | Pilot height | | 1.5 | | 1.5 | nominal | L1 |
| D | Shaft diameter | | 4 | | 4 | nominal | L1 |
| E | Shaft length | | 10 | | 10 | nominal | L1 |
| F | Shaft flat | | 3.5 | | 3.5 | nominal | L0 (nom: one source) |
| Lf | Flat length | | 7 | | 7 | nominal | L0 (nom: one source) |
Drawing

As a PDF: CC-NEMA-SZ-8x48.pdf.
What each maker states
- Mounting hole spacing A: makers range from 15.4 to 16 mm (Leadshine 15.4 mm, MOONS' 16 mm). The model uses the largest stated, 16 mm, so check your own motor's drawing before drilling a plate for it.
The 8x48 stepper motor beside the 8x42 and the 11x32
The 8x48 is number 3 of the 19 NEMA ICS 16 stepper motors published here, listed from 8x30 to 34x118.
- Body length (L): 48 mm on the 8x48 stepper motor, against 42 mm on the 8x42 and 32 mm on the 11x32.
- Body square (BD): up to 20.3 mm on the 8x48 stepper motor, against up to 20.3 mm on the 8x42 and up to 28.3 mm on the 11x32.
- Mounting hole spacing (A): 16 mm on the 8x48 stepper motor, against 16 mm on the 8x42 and 23 mm on the 11x32.
- Number of mounting holes (nh): 4 on the 8x48 stepper motor, the same on the 8x42 and the 11x32.
- Mounting hole thread (dt): 2 mm on the 8x48 stepper motor, against 2 mm on the 8x42 and 2.5 mm on the 11x32.
- Pilot diameter (N): 16 mm on the 8x48 stepper motor, against 16 mm on the 8x42 and 22 mm on the 11x32.
- Pilot height (T): 1.5 mm on the 8x48 stepper motor, against 1.5 mm on the 8x42 and 2 mm on the 11x32.
- Shaft diameter (D): 4 mm on the 8x48 stepper motor, against 4 mm on the 8x42 and 5 mm on the 11x32.
Other sizes
- One size smaller: 8x42 Stepper Motor, NEMA ICS 16, NEMA 8, up to 20.3 mm square, 42 mm long, 4 mm shaft, M2 mounting holes 16 mm apart, Anaheim Automation, Leadshine and MOONS' data.
- One size larger: 11x32 Stepper Motor, NEMA ICS 16, NEMA 11, up to 28.3 mm square, 32 mm long, 5 mm shaft, M2.5 mounting holes 23 mm apart, Leadshine, MOONS' and Oriental Motor data.
Conventions
- STEP AP214, millimetres, the mounting face at Z = 0 centred on the shaft's axis, the shaft along +Z.
Documents
Sources
anaheim-08y, leadshine-cm-steppers, moons-hybrid-steppers-figures, rule-nema-steppers-length. Full citations: the method page and this size's datasheet.
Found an error? Use the feedback section on this page.
Comments
Sign in to leave a comment.
Loading comments...