60t-8 Timing Pulley, GT2
The 60t-8 timing pulley (GT2 pulley) has 60 teeth on a 38.2 mm pitch diameter and an 8 mm bore; its flanges are 43.942 mm across and its hub 31.0388 mm, held by M4 set screws. Modeled as simplified STEP files.

How these parts are made, and what the levels mean: read the method
- Also known as: 60t-8 timing belt pulley, 60t-8 toothed pulley, 60t-8 belt pulley
- Model id:
gt2-pulleys-60t-8
- Standard: GT2 pulley · size 60t-8
Files
| Part key | Simplified |
|---|
gt2-pulleys-60t-8 | STEP |
Dimensions

| Symbol | Name | min | nom | max | Modeled | Rule | Level |
|---|
| dp | Pitch diameter | | 38.2 | | 38.2 | nominal | L1 |
| da | Outside diameter | | 37.69 | | 37.69 | nominal | L1 |
| df | Flange diameter | | 43.942 | | 43.942 | nominal | L1 |
| b | Face width between the flanges | | 7.366 | | 7.366 | nominal | L1 |
| bf | Width over the flanges | | 10.3 | | 10.3 | nominal | L0 (nom: one source) |
| L | Overall length | | 18.2626 | | 18.2626 | nominal | L1 |
| dh | Hub diameter | | 31.0388 | | 31.0388 | nominal | L1 |
| lh | Hub length | | 7.9756 | | 7.9756 | nominal | L0 (nom: one source) |
| de | Face diameter inside the flanges | | 33 | | 33 | nominal | L0 (nom: one source) |
| ds | Set screw thread | | 4 | | 4 | nominal | L1 |
Drawing

As a PDF: CC-GT2-SZ-60t-8.pdf.
The 60t-8 timing pulley beside the 40t-8
The 60t-8 is the last of the 7 GT2 pulley timing pulleys published here, listed from 16t-5 to 60t-8.
- Pitch diameter (dp): 38.2 mm on the 60t-8 timing pulley, against 25.46 mm on the 40t-8.
- Outside diameter (da): 37.69 mm on the 60t-8 timing pulley, against 24.96 mm on the 40t-8.
- Flange diameter (df): 43.942 mm on the 60t-8 timing pulley, against 30.734 mm on the 40t-8.
- Face width between the flanges (b): 7.366 mm on the 60t-8 timing pulley, the same on the 40t-8.
- Width over the flanges (bf): 10.3 mm on the 60t-8 timing pulley, the same on the 40t-8.
- Overall length (L): 18.2626 mm on the 60t-8 timing pulley, the same on the 40t-8.
- Hub diameter (dh): 31.0388 mm on the 60t-8 timing pulley, against 19.1516 mm on the 40t-8.
- Hub length (lh): 7.9756 mm on the 60t-8 timing pulley, the same on the 40t-8.
Other sizes
Conventions
- Simplified only: one aluminium solid, the toothed band as a plain cylinder at the outside diameter. STEP AP214, millimetres, the bore on Z, the outer flange's face at z = 0, the hub toward +Z.
- Images show illustrative teeth, not Gates' profile.
- Illustrative, not dimensioned by any source read: the flange rim, hub and bore chamfers, the set screws' place along the hub, and the teeth in the images.
Documents
Sources
gates-light-power-precision, misumi-gpa-2gt, sdpsi-gt2-molded-6mm. Full citations: the method page and this size's datasheet.
Found an error? Use the feedback section on this page.
Comments
Sign in to leave a comment.
Loading comments...