26.1 mm Desktop Hard Drive, SFF-8301 size drawing (PDF)

Datasheet — 26.1 mm Desktop Hard Drive, SFF-8301 by Milo

Open the PDF
26.1 mm Desktop Hard Drive, SFF-8301Get the CAD model26.1 mm Desktop Hard Drive, SFF-8301CC-DRIVE35-SZ-26.1.pdf

Text of this datasheet

3.5-inch drive envelope, 26.1 mm

Size drawing - 26.1 mm values on the views - SFF's envelope, the illustrative look on DO2 - scale 1:2

Source levels Sym. | Dimensio' 26.1 Main value = the modeled value (nominal, else the middle of Height, Al (SFF-8301; max only) € 26.10 min-max). Grey under a value = its min-max, Cie Cac wee 85 where the source gives both. ps = 101.60 Length, A2 (max only) < 147.00 = / = = the source gives only that limit, modeled at it. ref = reference. xs1 = 28.50 Side holes above the bottom, A10 6.35 L2 = the standard itself (or its complete free preview, or the maker's drawing). L1 = two or more independent sources agree: the release gate. ez = 3.50 Side to the bottom holes, A5 3.18 LO = one source only: printed amber

3.12-3.88 and marked *. Bottom holes across, A4 95.25

End to the first side hole, A&

Side holes apart, AQ

c =a source value was corrected; 41.28 the datasheet says how. House convention = a detail no

End to the first bottom holes, A7

First to second bottom holes, A6 44.45 source dimensions, drawn to a L s 147.00 stated house rule. This size's values: L2 21. 2.975 Notes 2.39-3.56 Values are SFF-8301 Rev 1.9 Table Lead-in @, section 3.1's example 4 ref 3-1 and SFF-8323 Rev 1.6 Table 3-1 (Option A). tp's main value is its midpoint; every 42.73 ret hole is threaded to its maximum, td. D, P, dt: 6-32 UNC-2B, Datum B width, A3 33.39 ref specs/unified-thread. cb is a reference: B is placed by cy. Drawn: SFF's envelope only, four 3.50 side and six bottom holes. The look 3.12-3.88 is on DO2. Datum B centre off the centreline, A11 20.68

First to third bottom holes, A13 76.20 D = 3.505, td = 3.56

Fastener penetration, min-max

Lead-in angle, section 3.1's example 90 ref

Connector width, A2 (SFF-8323)

D = 3.505, td = 3.56

Side to datum B, A13 13.43 ref

Connector centre height, A7

Connector height, AS 4.00 ref

Datum C to the first bottom holes, A8 36.38

yb2 = 95.25 Wee . . 6-32 UNC-2B major @ (computed from the inches) 3.505

cw = 42.73 ref Pitch (computed, 1/ 32 inch) 0.794

Tap drill, the drill point's start (computed) 2.705

Full thread depth, every hole (tp max) 3.56

yb = 3.18 4

xb1 = 41.28 pb2 = 44.45

pb3 = 76.20

TITLE

'? CommunityCAD Size drawing, 26.1mm

STANDARDS FOLLOWED FAMILY / DETAIL

SFF-8301 Rev 1.9 - SFF-8323 Rev 1.6 (SNIA) 3.5-inch drive - 26.1 mm

SHEET REV SCALE PROJECTION UNITS CC-DRIVE35-SZ-26.1 A 1:2 € Dimensions in mm SPEC VERSION LICENSE PAGE cfd05b053c736a4F15ba3030aa41febd40cdc205 CC-BY 4.0 IronPixel Labs LLC 1/1

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.