'?) CommunityCAD
CC-DRIVE35-DS-26.1 revA Size datasheet - 26.1 mm
SFF-8301 26.1 mm drive
Size datasheet: this size's values with their levels, conventions and sources.
26.1mm, front view, 1:5
hs xsi ps yb yb2 xb1 pb2 pb3 tp
du al cw cs cb
cz
cy ch cc D
P
dt td
ra |
Dimension Height, Al (SFF-8301; max only) Width, A3 + Al]
Length, A2 (max only)
Side holes above the bottom, A10 End to the first side hole, A8 Side holes apart, A9
Side to the bottom holes, A5 Bottom holes across, A4
End to the first bottom holes, A7 First to second bottom holes, A6 First to third bottom holes, A13
Fastener penetration, min-max
Lead-in @, section 3.1's example Lead-in angle, section 3.1's example Connector width, A2 (SFF-8323) Datum B width, A3
Side to datum B, A13
Connector centre height, A7
Datum B centre off the centreline, AN) Connector height, A5
Datum C to the first bottom holes, A&
6-32 UNC-2B major @ (computed from the inches)
Pitch (computed, 1 / 32 inch) Tap drill, the drill point's start (computed)
Full thread depth, every hole (tp max)
26.1 mm, view from above, 1:5
Part key drives-3-5-26-1 Files 2 STEP AP214 (simplified + threaded)
Value < 26.10 101.35-: 101.85 $< 147.00 * 6.35 28.50 101.60 3.18 95.25 41.28 l2- 44.45 l2- 76.20 2-4 2.39-3.56 42.73 ref 33.39 ref 13.43 ref SoilZs 3.88 4.00 ref 3.505 computed 0.794 computed 2.705 computed 3.56 computed
Modeled value: nominal, else the midpoint of min-max. < / 2: only that limit is given, modeled at it. * amber: one source (LO). house: a stated house rule. Level - independent sources.
SFF-8301 Rev 1.9 - SFF-8323 Rev 1.6 (SNIA)
3.5-inch drive - 26.1 mm - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
Page 1/2
spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205
---
CC-DRIVE35-DS-26.1 revA Size datasheet - 26.1mm
'?) CommunityCAD
Conventions
e Envelope and frame: SFF-8301's form factor: Al and A2 are maxima only, so the box is at them; W at A3's nominal. Bottom face (datum Z) at z = 0, the connector end toward +X, the width centred on Y, the connector toward -Y.
« Mounting holes: 6-32 UNC-2B, four side holes (no middle hole: optional in SFF, #1368 item 3 A) and six bottom holes (all three SFF pairs), blind, full thread to tp's maximum (#1368 item 2 A), then a 118° drill point at the tap drill. Simplified: plain bores at D, thread in the metadata. The makers' deeper depths aren't modeled.
« Lead-in: SFF-8301 section 3.1 requires a lead-in and gives one example, a dl countersink at al: the model uses that example at every hole.
e Connector: SFF-8323 Option A: a block cw x ch on datum B's centreline, cy off the drive's, its centre cz up, its face in the end's plane; the keep-out under it open to datum C. No blades or latch recesses (an envelope, no ECAD).
¢ House look: Illustrative, not drawn here: a black cast base with a rim and parting groove, a bright stainless stamped cover with Torx screws, a paper label with the CommunityCAD mark, a green board and chips underneath, a light grey SATA connector with its keys and gold contacts, a jumper block. Each a share of a sourced value, inside the envelope. No maker text.
Sources
Source Publisher Retrieved sha256
sff8301-r1-9 SNIA SFF TA TWG 2026-11-05 232e339bfc96 (kept outside the repo) sff8323-r1-6 SNIA SFF TA TWG (SFF Committee) 2026-11-05 516117569540 (kept outside the repo) seagate-100845789F Seagate Technology LLC 2026-11-05 1cf4ba39e5bf (kept outside the repo) seagate-100844774h Seagate Technology LLC 2026-11-06 3807a0be4fb3 (kept outside the repo) wd-he550-r1-7-figures Western Digital Corporation 2026-11-05 837f35c5ba15 (kept outside the repo) toshiba-mg07aca-r02-figures Toshiba Electronic Devices & Storage 2026-11-05 3410eefac39c (kept outside the repo)
Corporation
The whole series (verification map, drawings): CC-DRIVE35-DS.
SFF-8301 Rev 1.9 - SFF-8323 Rev 1.6 (SNIA) Page 2/2 3.5-inch drive - 26.1 mm - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
