51101 Thrust Bearing, ISO 104

STL Supports CommunityCAD0 downloads
51101 Thrust Bearing, ISO 104
1 / 5

51101 Thrust Bearing, ISO 104

For a 12 mm shaft and a 26 mm housing bore, the 51101 thrust bearing (ISO 104) is 9 mm high. Modeled as simplified STEP files.

51101 thrust bearing, ISO 104

How these parts are made, and what the levels mean: read the method

  • Also known as: 51101 thrust ball bearing, 51101 axial ball bearing, 51101 axial bearing
  • Model id: iso104-51101
  • Standard: ISO 104 · size 51101

Files

Part keySimplified
iso104-51101STEP

Dimensions

Dimension symbols for 51101 thrust bearings (ISO 104)

SymbolNameminnommaxModeledRuleLevel
dShaft washer bore diameter1212nominalL1
DHousing washer outside diameter2626nominalL1
THeight99nominalL1
rChamfer dimension0.30.3single limit (min), modeled at the limitL1
d1Shaft washer outside diameter26 ref26reference valueL1
D1Housing washer bore diameter13 ref13reference valueL1

Drawing

Drawing of the 51101 thrust bearing with its values (ISO 104)

As a PDF: CC-ISO104-SZ-51101.pdf.

The 51101 thrust bearing beside the 51100 and the 51102

The 51101 is number 2 of the 9 ISO 104 thrust bearings published here, listed from 51100 to 51108.

  • Shaft washer bore diameter (d): 12 mm on the 51101 thrust bearing, against 10 mm on the 51100 and 15 mm on the 51102.
  • Housing washer outside diameter (D): 26 mm on the 51101 thrust bearing, against 24 mm on the 51100 and 28 mm on the 51102.
  • Height (T): 9 mm on the 51101 thrust bearing, the same on the 51100 and the 51102.
  • Chamfer dimension (r): at least 0.3 mm on the 51101 thrust bearing, the same on the 51100 and the 51102.
  • Shaft washer outside diameter (d1): 26 mm (reference) on the 51101 thrust bearing, against 24 mm (reference) on the 51100 and 28 mm (reference) on the 51102.
  • Housing washer bore diameter (D1): 13 mm (reference) on the 51101 thrust bearing, against 11 mm (reference) on the 51100 and 16 mm (reference) on the 51102.

Other sizes

Conventions

  • Simplified only: two washers joined by a web, internals not modeled, no balls or cage. STEP AP214, millimetres, Z along the axis, the housing washer's back face at Z = 0.
  • Shaft washer bore d, housing washer outside diameter D and height T at their nominals; washers concentric, the housing washer's back face at Z = 0.
  • A solid web joins the washers in the middle half of the band between D1 and d1; balls, cage and raceway grooves not modeled.

Documents

Sources

nsk-thrust, ntn-bearingfinder-thrust, skf-17000-thrust. Full citations: the method page and this size's datasheet.

Found an error? Use the feedback section on this page.

Comments

Sign in to leave a comment.

Loading comments...

From the datasheet

docs/CC-ISO104-DS-51101.pdf

. CC-1$0184-DS$-51101 rev A '?) CommunityCAD Size datasheet - 51101 ISO 104 51101 thrust ball bearing Size datasheet: this bearing's values with their levels, conventions and sources. For 12 mm shafts, axial loads in one direction Part key iso104-51101 Files 1 STEP AP214 (simplified) 51101, front…

View full datasheet →

docs/CC-ISO104-SZ-51101.pdf

ISO 104 single direction thrust ball bearing, 51101 Size drawing - 51101 values on the views - enlarged 2:1 Bearing 51101 9 26.000 ref 13.000 ref Source levels Main value = the modeled value (nominal, else the middle of min-max). d1 = 26.000 ref Grey under a value = its min-max, where the source…

View full datasheet →