slot 10 M6 Slide-in T-slot Nut datasheet (PDF)

Datasheet — slot 10 M6 Slide-in T-slot Nut by Milo

Open the PDF
slot 10 M6 Slide-in T-slot NutGet the CAD modelslot 10 M6 Slide-in T-slot NutCC-TNUTS-DS-s10-M6.pdf

Text of this datasheet

CC-TNUTS-DS-s10-Mé6 rev A Size datasheet - s10-M6

'?) CommunityCAD

slot 10 M6 slide-in T-slot nut

Size datasheet: this size's values with their levels, conventions and sources.

For slot 10 aluminium extrusions Part key slot-nuts-slide-in-s10-m6 q J Files 2 STEP AP214 (simplified, threaded)

$10-M6, top, 1:1 s10-M6, end, 2:1 (hidden lines dashed) Sym. Dimension Value Level Ww Body width across the slot 17 L1- 2 1 Body length along the slot 17x lo -1 b Neck width 9.8 L1- 2 h Overall height 9 L1- 2 k Body height 6 L1- 2 n Neck height 3 L1- 2

Modeled value: nominal, else the midpoint of min-max. < / =: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources.

No published standard (makers' drawings) Page 1/2 Slide-in T-slot nut - s10-M6 - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 304229b833a653b73db51178a38d40486ee7c36b

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.

---

* CC-TNUTS-DS-s10-Mé6 rev A '?) CommunityCAD Size datasheet - s10-M6

Conventions

« Lead-ins and flanks: 45 degree chamfers of I/10 on the four corners at the nut's two ends, and the body's lower edges chamfered 45 degrees by k/2. Both illustrative, not any maker's dimensions.

« Values: No published standard: each value the reference maker's drawing (Misumi). A second maker's value counts as agreeing where the slot leaves room for the difference, computed from the profile's data, and a size where a value stands on one maker is labelled single source.

¢ Fit: A nut is checked against its slot system's one-cell profile, never fitted to it: neck no wider than the opening, width no wider than the undercut, body no taller than the cavity.

« Finish: Brushed stainless: render and metadata only. No markings, no serrations, other edges sharp. Bottom face at Z = 0, the neck toward +Z.

Sources

Source Publisher Retrieved sha256

misumi-slide-in-nuts MISUMI 2026-11-02 #9cc15la2bdf (kept outside the repo) motedis-slide-in-nuts Motedis 2026-11-03 ad7e2de57163 (kept outside the repo) rule-motedis-slide-in-nut-heights CommunityCAD 2026-11-03 ef27c54b7F3c pule-misumi-slide-in-nut-neck CommunityCAD 2026-11-03 9a8798514ca2

The whole series (verification map, corrections, drawings): CC-TNUTS-DS.

No published standard (makers' drawings) Page 2/2 Slide-in T-slot nut - s10-M6 - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 304229b833a653b73db51178a38d40486ee7c36b

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.