CC-1S04035-DS-M8 revA Size datasheet - M8
'?) CommunityCAD
ISO 4035 M8 hexagon thin nut
Size datasheet: this size's values with their levels, conventions and sources.
Thread M8 x 1.25, ISO metric coarse, right hand
Part key iso4035-m8
Files 2 STEP AP214 (simplified + threaded)
Simplified - M8, front view, 2.5:1 Threaded - M8, front view, 2.5:1
Sym. Dimension Value P Thread pitch 25 s Width across flats 12.865 12.73-13.00
e Width across corners 14.38 pos | m Nut height 3.85 3.70-4.00
mw Wrenching height 3.0
dw Bearing face diameter 11.60 pee | da Countersink diameter 8.375 8.00-8.75 B Corner chamfer angle, deg 22.5 15-30 8 Countersink angle, deg 115 110-120 D1 Basic minor diameter (crests) 6.6468
tap Tap drill (method D - P) 6.75 l1 +2
Modeled value: nominal, else the midpoint of min-max. < / 2: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources. e follows from s and is checked = e min; dw min sets the chamfer's face circle; mw min is checked at mid-flat.
ISO 4035:2012 - ISO 68-1/ ISO 261 (thread) Page 1/2 Hexagon nut - M8 - both detail levels - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec 82d0e3f1e4052a4ec559d0F9Fd7b4cF7b5772671
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
---
CC-1S04035-DS-M8 revA Size datasheet - M8
'?) CommunityCAD
Conventions
e Hexagon: regular at the modeled s (the middle of its band), one corner on +X, sharp edges.
« Corner chamfer on both faces: a cone at B (range midpoint) meeting the face on (dw min + s) / 2. Not specified by the standard. « Countersink on both faces at da and 9, both at their range midpoints.
¢ Bore: plain at D (simplified); ISO 68-1 basic internal thread over the full height (threaded), cut by the countersinks.
« No washer face, no markings. Values given only as a limit are modeled at that limit. Features the standard does not dimension are house conventions.
Sources
Source Publisher Retrieved sha256
amesweb-tap-drill AMESweb 2026-10-23 e6501cc1414a
pule-tap-drill CommunityCAD 2026-10-23 625b582c306e
pule-basic-minor CommunityCAD 2026-10-23 00329692204
fasten-it-iso4035 fasten.it 2026-10-25 3849b4c60b37
engineersedge-iso4035 Engineers Edge 2026-10-25 b8755da99aeb
boltport-iso4035 Boltport 2026-10-25 78a545de5f60
iso4035-2012-sample ISO (preview published by iTeh Standards) n/a 6172bfee8723 (kept outside the repo) fuller-iso4035 Fuller Fasteners 2026-10-25 2899f6c7F2b1
The whole series (verification map, corrections, drawings): CC-ISO4035-Ds.
ISO 4035:2012 - ISO 68-1/ ISO 261 (thread) Page 2/2 Hexagon nut - M8 - both detail levels - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec 82d0e3f1e4052a4ec559d0F9Fd7b4cF7b5772671
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.