'?) CommunityCAD
CC-1S010511-DS-M8 rev A Size datasheet - M8
ISO 10511 M8 nylon insert lock nut
Size datasheet: this size's values with their levels, conventions and sources.
Simplified - M8, front view, 2.5:1 Threaded - M8, front view, 2.5:1 Sym. Dimension P Thread pitch s Width across flats e Width across corners m Hexagon height h Nut height (to the collar top) mw Wrenching height dw Bearing face diameter da Countersink diameter B Corner chamfer angle, deg 8 Countersink angle, deg D1 Basic minor diameter (crests) tap Tap drill (method D - P)
Thread M8 x 1.25, ISO metric coarse, right hand
Part key iso10511-m8
Files 2 STEP AP214 (simplified + threaded)
Value 25
12.865 12.73-13.00
2 14.38 2 3.70
6.47 6.18-6.76
2 2.96 2 11.60
8.375 8.00-8.75
22.5 15-30
105 90-120
6.6468
6.75 ll. 2
Modeled value: nominal, else the midpoint of min-max. < / =: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources. e follows from s and is checked = e min; dw min sets the chamfer's face circle and the collar; mw min is checked at
mid-flat.
ISO 10511:2012 (withdrawn) - ISO 68-1/ ISO 261 (thread)
Lock nut - M8 - both detail levels - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
Page 1/2 spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205
---
CC-1S010511-DS-M8 rev A Size datasheet - M8
'?) CommunityCAD
Conventions
e Hexagon: regular at the modeled s (the middle of its band), one corner on +X, sharp edges.
« Corner chamfer on both hexagon faces: a cone at B (range midpoint) meeting the face on (dw min + s) / 2. Not specified by the standard.
« Countersink on the bearing face at da and 8, both at their range midpoints.
¢ Collar dw min across from m to h, wall and lip t = (dw min - D) / 4, top edge rounded at t; the nylon insert its own solid from m to h - t. Not specified by the standard.
« Bore: plain at D (simplified); ISO 68-1 basic internal thread through m, insert bore at D1 (threaded).
« No washer face, no markings. Values given only as a limit are modeled at that limit. Features the standard does not dimension are house conventions.
Sources Source Publisher Retrieved sha256 amesweb-tap-drill AMESweb 2026-10-23 e6501cc1414a pule-tap-drill CommunityCAD 2026-10-23 625b582c306e pule-basic-minor CommunityCAD 2026-10-23 00329692204 fasten-it-iso10511 fasten.it 2026-10-25 2f7b7c8F22c9 iso10511-2012-sample ISO (preview published by iTeh Standards) n/a d8f9b2cébe33 (kept outside the repo)
The whole series (verification map, corrections, drawings): CC-ISO10511-DS.
ISO 10511:2012 (withdrawn) - ISO 68-1/ ISO 261 (thread) Page 2/2 Lock nut - M8 - both detail levels - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
