* CC-DIN1587-DS-M8 rev A '?) CommunityCAD Size datasheet - M8
DIN 1587 M8 acorn nut (hexagon domed cap nut)
Size datasheet: this size's values with their levels, conventions and sources.
Thread M8 x 1.25, ISO metric coarse, right hand Part key din1587-m8 Files 2 STEP AP214 (simplified + threaded) Simplified - M8, front view, 1:1 Threaded - M8, front view, 1:1 Sym. Dimension Value Level P Thread pitch 1.25 l1 + 2 s Width across flats 13 L1- 3 12. 73-13 e Width across corners > 14.38 L1- 2 m Hexagon height 6.32c l1 + 2 6.14-6.5 mw Wrenching height > 4.91 Lo- 1 h Overall height 15 L1- 2 14.57-15 dk Dome diameter < 12.5 L1- 3 (P Dome radius 6.25 ref L1- 2 t Bore depth (full diameter) 11.00 L1- 2 10.65-11.35 x Thread run-out < 2.5 L1- 2 w Wall, bore to dome top >2 L1- 2 dw Bearing face diameter > 11.6* lo- 4 da Countersink diameter 8.375% Lo- 1 8-8.75 B Corner chamfer angle, deg 22.5% Lo- 1 15-30 8 Countersink angle, deg 120* lo - 1 D1 Basic minor diameter (crests) 6.6468 L1-2 tap Tap drill (method D - P) 6.75 L1- 2
Modeled value: nominal, else the midpoint of min-max. < / 2: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources. e follows from s and is checked = e min; dw min and dk set the two chamfer circles; mw min is checked at mid-flat, w min on the axis; x is the threaded run-out.
DIN 1587:2000 - ISO 4759-1 (m min) - ISO 68-1/ ISO 261 (thread) Page 1/2 Acorn nut - M8 - both detail levels - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
---
* CC-DIN1587-DS-M8 rev A '?) CommunityCAD Size datasheet - M8
Conventions
« Hexagon: regular at the modeled s (its nominal), one corner on +X, sharp edges.
« Corner chamfers: a cone at B (range midpoint) at both ends, meeting the bearing face on (dw min + s) / 2 and the hex top face on (dk + s) / 2. Not specified by the standard.
e Dome: a cylinder of dk to h - r, then a hemisphere of r with its top at h.
« Countersink at the bearing face at da (range midpoint) and 6.
« Bore: blind, plain at D to t (simplified); ISO 68-1 basic internal thread, full to t - x and fading over x (threaded), cut by the countersink. It ends in a 120° drill point at the tap drill, which leaves w min.
« No washer face, no markings. Values given only as a limit are modeled at that limit. Features the standard does not dimension are house conventions.
Sources
Source Publisher Retrieved sha256
amesweb-tap-drill AMESweb 2026-10-23 e6501cc1414a
pule-tap-drill CommunityCAD 2026-10-23 625b582c306e
pule-basic-minor CommunityCAD 2026-10-23 00329692204 pule-iso4759-1-nut-height CommunityCAD 2026-10-27 5058ea2d5898
fasten-it-din1587 fasten.it 2026-10-26 27ecd8a57bca
fasteners-eu-din1587 fasteners.eu 2026-10-26 67e68854e2a schrauben-lexikon-din1587 schrauben-lexikon.de (Wegertseder) 2026-10-26 27cb9268242e fasteners-eu-din1587-drawing _ fasteners.eu 2026-10-26 beb68a781805 (kept outside the repo)
The whole series (verification map, corrections, drawings): CC-DIN1587-DS.
DIN 1587:2000 - ISO 4759-1 (m min) - ISO 68-1/ ISO 261 (thread) Page 2/2 Acorn nut - M8 - both detail levels - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
