* CC-HSINSERT-DS-M6x12.7 revA '?) CommunityCAD Size datasheet - M6x12.7
M6x12.7 heat-set insert
Size datasheet: this size's values with their levels, conventions and sources.
For M6 screws in 3D-printed and al moulded plastic
C7) Part key heat-set-inserts-m6x12-7 Ha Files 2 STEP AP214 (simplified, Hi threaded) M6x12.7, top, 2.5:1 M6x12.7, side, 1.5:1 (hidden lines dashed)
Sym. Dimension Value Level
L Length 12.7 l1 + 2
di Knurl outside diameter 8.7 L1- 2
d2 Pilot diameter 7.9% Lo- 1
Modeled value: nominal, else the midpoint of min-max. s / =: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources.
No published standard (makers' tables) Page 1/2 Heat- set threaded insert - M6x12.7 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec 1431dca0786db211c4968b488128bféd30bccS5db
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
---
* CC-HSINSERT-DS-M6x12.7 revA '?) CommunityCAD Size datasheet - M6x12.7
Conventions
e Knurl and pilot: Two knurled bands of opposite hand, a groove, a lead and a pilot: their proportions are illustrative, not any maker's design, measured for fit only. Only L, d1 and d2 come from the makers' tables.
e Thread: Simplified: plain bands at d1 and a plain bore at the nominal diameter, so it mates with simplified screws. Threaded: the ISO 68-1 basic internal profile, right hand, the full length, with a 90 degree countersink to the nominal diameter at both ends.
« Values: No published standard: makers' tables. L and d1 count as agreeing only between ruthex and CNC Kitchen; RS PRO counts with ruthex. d2 may stand on ruthex alone, and on CNC Kitchen's three shortest inserts it is ruthex's from the next longer insert with the same thread and d1. Sizes on one maker's table are labelled single source.
« Finish: Polished lead-free brass: render and metadata only. No markings, other edges sharp. Top face, flush with the part's surface, at Z = 0, the pilot end at Z = -L.
« Recommended hole, per maker: CNC Kitchen 8.1 mm, RS PRO 8.0 mm, ruthex 8.0 mm.
« Wall around the hole, per maker: CNC Kitchen 3.3 mm, RS PRO 3.3 mm, ruthex 3.3 mm.
e Minimum hole depth, per maker: CNC Kitchen 13.7 mm, ruthex 13.7 mm.
e The hole depth is each maker's callout on its drawing added to that maker's L, read twice by Claude, and the two reads agree (ADR 0055).
* CNC Kitchen's values for this size are figure reads: its table is an image, read twice by Claude, and the two reads agree (ADR 0055).
Sources Source Publisher Retrieved sha256 ruthex-inserts ruthex GmbH (as published by 3D Jake GmbH) 2026-10-30 ef2e07cebd47 rspro-inserts RS Components (RS PRO own brand), as hosted by 2026-10-30 d3b903287ea6 (kept outside the repo) Distrelec cenckitchen-inserts CNC Kitchen (Stefan Hermann) 2026-10-30 dbe75444a09F (kept outside the repo)
The whole series (verification map, corrections, drawings): CC- HSINSERT- DS.
No published standard (makers' tables) Page 2/2 Heat- set threaded insert - M6x12.7 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec 1431dca0786db211c4968b488128bféd30bccS5db
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.