M6 Thin Hex Nut, ISO 4035 datasheet (PDF)

Datasheet — M6 Thin Hex Nut, ISO 4035 by Milo

Open the PDF
M6 Thin Hex Nut, ISO 4035Get the CAD modelM6 Thin Hex Nut, ISO 4035CC-ISO4035-DS-M6.pdf

Text of this datasheet

. CC-1S04035-DS-Mé rev A '?) CommunityCAD Size datasheet - M6

ISO 4035 M6 hexagon thin nut

Size datasheet: this size's values with their levels, conventions and sources.

Thread M6 x 1, ISO metric coarse, right hand

Part key iso4035-m6

Files 2 STEP AP214 (simplified + threaded)

Simplified - M6, front view, 3:1 Threaded - M6, front view, 3:1

Sym. Dimension Value P Thread pitch 1 s Width across flats 9.89 9. 78-10 .08

e Width across corners 2 11.05 = m Nut height 3.05 2.90-3.20

mw Wrenching height 2.3

dw Bearing face diameter 2 8.90 = da Countersink diameter 6.375 6.00-6.75 B Corner chamfer angle, deg 22.5 15-30 8 Countersink angle, deg 115 110-120 D1 Basic minor diameter (crests) 4.9175

tap Tap drill (method D - P) 5 Li + 2

Modeled value: nominal, else the midpoint of min-max. < / =: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources. e follows from s and is checked = e min; dw min sets the chamfer's face circle; mw min is checked at mid-flat.

ISO 4035:2012 - ISO 68-1/ ISO 261 (thread) Page 1/2 Hexagon nut - M6 - both detail levels - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.

---

CC-1S04035-DS-Mé revA Size datasheet - M6

'?) CommunityCAD

Conventions

e Hexagon: regular at the modeled s (the middle of its band), one corner on +X, sharp edges.

« Corner chamfer on both faces: a cone at B (range midpoint) meeting the face on (dw min + s) / 2. Not specified by the standard. « Countersink on both faces at da and 9, both at their range midpoints.

¢ Bore: plain at D (simplified); ISO 68-1 basic internal thread over the full height (threaded), cut by the countersinks.

« No washer face, no markings. Values given only as a limit are modeled at that limit. Features the standard does not dimension are house conventions.

Sources

Source Publisher Retrieved sha256

amesweb-tap-drill AMESweb 2026-10-23 e6501cc1414a

pule-tap-drill CommunityCAD 2026-10-23 625b582c306e

pule-basic-minor CommunityCAD 2026-10-23 00329692204

fasten-it-iso4035 fasten.it 2026-10-25 3849b4c60b37

engineersedge-iso4035 Engineers Edge 2026-10-25 b8755da99aeb

boltport-iso4035 Boltport 2026-10-25 78a545de5f60

iso4035-2012-sample ISO (preview published by iTeh Standards) n/a 6172bfee8723 (kept outside the repo) fuller-iso4035 Fuller Fasteners 2026-10-25 2899f6c7f2b1

The whole series (verification map, corrections, drawings): CC-ISO4035-DS.

ISO 4035:2012 - ISO 68-1/ ISO 261 (thread) Page 2/2 Hexagon nut - M6 - both detail levels - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.