'?) CommunityCAD
CC-1S010511-DS-Mé revA Size datasheet - M6
ISO 10511 M6 nylon insert lock nut
Size datasheet: this size's values with their levels, conventions and sources.
mw dw
da
D1
tap
Dimension
Thread pitch
Width across flats
Width across corners Hexagon height
Nut height (to the collar top)
Wrenching height Bearing face diameter
Countersink diameter
Corner chamfer angle, deg
Countersink angle, deg
Basic minor diameter (crests)
Tap drill (method D - P)
Threaded - M6, front view, 3:1
Thread M6 x 1, ISO metric coarse, right hand
Part key iso10511-m6
Files 2 STEP AP214 (simplified + threaded)
Value Level 1
9.89 9. 78-1000
2 11.05 2 2.90
5.76 5.52-6.00
2 2.32 2 8.90
6.375 6.00-6.75
22.5 15-30
105 90-120
L2 - 2 L1 + 2
4.9175
5 L1- 2
Modeled value: nominal, else the midpoint of min-max. < / 2: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources. e follows from s and is checked = e min; dw min sets the chamfer's face circle and the collar; mw min is checked at
mid -flat.
ISO 10511:2012 (withdrawn) - ISO 68-1 / ISO 261 (thread) Lock nut - M6 - both detail levels - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
Page 1/2 spec 82d0e3f1e4052a4ec559d0F9Fd7b4cF7b5772671
---
* CC-1S010511-DS-Mé revA '?) CommunityCAD Size datasheet - M6
Conventions
e Hexagon: regular at the modeled s (the middle of its band), one corner on +X, sharp edges.
« Corner chamfer on both hexagon faces: a cone at B (range midpoint) meeting the face on (dw min + s) / 2. Not specified by the standard.
« Countersink on the bearing face at da and 8, both at their range midpoints.
¢ Collar dw min across from m to h, wall and lip t = (dw min - D) / 4, top edge rounded at t; the nylon insert its own solid from m to h - t. Not specified by the standard.
« Bore: plain at D (simplified); ISO 68-1 basic internal thread through m, insert bore at D1 (threaded).
« No washer face, no markings. Values given only as a limit are modeled at that limit. Features the standard does not dimension are house conventions.
Sources Source Publisher Retrieved sha256 amesweb-tap-drill AMESweb 2026-10-23 e6501cc1414a pule-tap-drill CommunityCAD 2026-10-23 625b582c306e pule-basic-minor CommunityCAD 2026-10-23 00329692204 fasten-it-iso10511 fasten.it 2026-10-25 2f7b7c8F22c9 iso10511-2012-sample ISO (preview published by iTeh Standards) n/a d8f9b2cé6bce33 (kept outside the repo)
The whole series (verification map, corrections, drawings): CC-ISO10511-Ds.
ISO 10511:2012 (withdrawn) - ISO 68-1 / ISO 261 (thread) Page 2/2 Lock nut - M6 - both detail levels - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 82d0e3f1e4052a4ec559d0F9Fd7b4cF7b5772671
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.