M6 Hex Head Screw, ISO 4017 datasheet (PDF)

Datasheet — M6 Hex Head Screw, ISO 4017 by Milo

Open the PDF
M6 Hex Head Screw, ISO 4017Get the CAD modelM6 Hex Head Screw, ISO 4017CC-ISO4017-DS-M6.pdf

Text of this datasheet

'?) CommunityCAD

CC-1S04017-DS-Mé revA

Size datasheet - M6

ISO 4017 M6 hexagon head screw

Size datasheet: this size's values with their levels, its lengths, conventions and sources.

Simplified - M6x20, front view, 2.5:1

kw

dw

da

di tap

a

Dimension Thread pitch

Width across flats

Width across corners

Head height

Wrenching height

Washer face height

Bearing face diameter

Head top chamfer, deg

Underhead fillet radius

Transition diameter

Thread run-out under head

Basic minor diameter (end face)

Tap drill (method d - P)

End chamfer angle, deg

Thread

Lengths Files

Threaded - M6x20, front view, 2.5:1

hand

threaded)

Value 1

9.89 9.78-10.00

2 11.05

4.0 3.85-4.15

2 2.70

0.325 0.15-0.50

2 8.88

22.5 15-30

2 0.25 < 6.8

2.00 1.00-3.00

4.9175 5 < 50

M6 x 1, ISO metric coarse, right

11 generated, | = 12-60 22 STEP AP214 (simplified +

Level

L2-4 L1 - 2 L1 - 2

Modeled value: nominal, else the midpoint of min-max. < / 2: only that limit is given, modeled at the limit. * amber: one source (LO). c: a source

value was corrected. Level - independent sources.

ISO 4017:2022 - ISO 4753:2011 (ends) - ISO 68-1/ ISO 261 (thread) Hex head screw - M6 - both detail levels - Dimensions in mm : CC-BY 4.0, lronPixel Labs LLC

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.

Page 1/2

spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205

---

CC-1S04017-DS-Mé revA Size datasheet - M6

'?) CommunityCAD

Lengths | Thread Is Ig Part key 12 to the head - - iso04017-m6x12 16 to the head - - is04017-m6x16 20 tothe head - - iso4017-m6x20 25 to the head - - iso4017-m6x25 30 tothe head - - is04017-m6x30 35 tothe head = - is04017-m6x35 4Q tothe head - - iso04017-m6x40 45 to the head - - is04017-m6x45 50 tothe head - - is04017-m6x50 55 to the head - - is04017-m6x55 60 to the head - - iso04017-m6x60

Threaded to the head: the full thread from a (middle of 1P-3P).

Conventions

« End: ISO 4753 chamfered end (CH), end face at d1, chamfer at the angle limit.

« Head: hexagon at the modeled s, one corner on +X; washer face (dw min + s) / 2, c high; top chamfer at B (house construction, ADR 0052 amendment 1).

¢ Thread (threaded level): ISO 68-1 basic profile, right hand.

« Values given only as a limit are modeled at that limit. Features the standard does not dimension are house conventions.

Sources

Source Publisher Retrieved sha256

amesweb-tap-drill AMESweb 2026-10-23 e6501cc1414a

pule-tap-drill CommunityCAD 2026-10-23 625b582c306e

pule-basic-minor CommunityCAD 2026-10-23 00329692204

iso4753-2011-sample ISO (preview published by iTeh Standards) n/a 7526d25f9381 (kept outside the repo) iso4017-2022-sample ISO (preview published by iTeh Standards) n/a #41658422832 (kept outside the repo) iso4017-2022-sample-figure ISO (preview published by iTeh Standards) n/a £41658422832 (kept outside the repo) iso4014-2022-sample ISO (preview published by iTeh Standards) n/a 2e44b7555604 (kept outside the repo) fasten-it-iso4017 fasten.it 2026-10-25 395693958e2b

fasten-it-iso4014 fasten.it 2026-10-25 50a81d6072b8

fasteners-eu-iso4017 fasteners.eu 2026-10-25 161753a8c338

globalfastener-iso4017 globalfastener.com (Internet Archive copy, 2026-10-25 6c30078c626e

captured 2020-07-12)

globalfastener-iso4017-2022 globalfastener.com (Internet Archive copy, 2026-10-25 9aa6930a2aa3 captured 2026-03-16)

fuller-iso4014 Fuller Fasteners 2026-10-25 1130347fbf24 engineersedge-iso4014-4017 Engineers Edge 2026-10-25 1466bfae2ba8

The whole series (verification map, corrections, drawings): CC-ISO4017-DS.

ISO 4017:2022 - ISO 4753:2011 (ends) - ISO 68-1/ ISO 261 (thread) Page 2/2 Hex head screw - M6 - both detail levels - Dimensions in mm : CC-BY 4.0, lronPixel Labs LLC spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.