CC-DIN1587-DS-M5 revA Size datasheet - M5
'?) CommunityCAD
DIN 1587 M5 acorn nut (hexagon domed cap nut)
Size datasheet: this size's values with their levels, conventions and sources.
Thread M5 x 0.8, ISO metric coarse, right hand Part key din1587-m5 Files 2 STEP AP214 (simplified + threaded) Simplified - M5, front view, 2:1 Threaded - MS5, front view, 2:1 Sym. Dimension Value Level P Thread pitch 0.8 L1- 2 s Width across flats 8 L1- 3 7.78-8 e Width across corners > 8.79 L1- 2 m Hexagon height 3.85c l1 + 2 3.7-4 mw Wrenching height 2 2.96% lo- 1 h Overall height 10 L1- 2 9.64-10 dk Dome diameter < 7.5 L1- 3 Pr Dome radius 3.75 ref l1 + 2 t Bore depth (full diameter) 7.50 L1- 2 7.21-7.79 x Thread run-out < 1.6 L1- 2 w Wall, bore to dome top >2 L1- 2 dw Bearing face diameter 2 6.9% lo-1 da Countersink diameter 5.375% Lo - 1 5-5.75 B Corner chamfer angle, deg 22.5% Lo - 1 15-30 8 Countersink angle, deg 120* Lo - 1 D1 Basic minor diameter (crests) 4.134 L1-2 tap Tap drill (method D - P) 4.2 La - 2
Modeled value: nominal, else the midpoint of min-max. s / =: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources. e follows from s and is checked = e min; dw min and dk set the two chamfer circles; mw min is checked at mid-flat, w min on the axis; x is the threaded run-out.
DIN 1587:2000 - ISO 4759-1 (m min) - ISO 68-1 / ISO 261 (thread) Page 1/2 Acorn nut - M5 - both detail levels - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 82d0e3f1e4052a4ec559d0F9Fd7b4cF7b5772671
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
---
CC-DIN1587-DS-M5 revA Size datasheet - M5
'?) CommunityCAD
Conventions
« Hexagon: regular at the modeled s (its nominal), one corner on +X, sharp edges.
« Corner chamfers: a cone at B (range midpoint) at both ends, meeting the bearing face on (dw min + s) / 2 and the hex top face on (dk + s) / 2. Not specified by the standard.
« Dome: a cylinder of dk to h - r, then a hemisphere of r with its top at h.
« Countersink at the bearing face at da (range midpoint) and 0.
« Bore: blind, plain at D to t (simplified); ISO 68-1 basic internal thread, full to t - x and fading over x (threaded), cut by the countersink. It ends flat at t: a 120° drill point wouldn't leave w min.
« No washer face, no markings. Values given only as a limit are modeled at that limit. Features the standard does not dimension are house conventions.
Sources
Source Publisher Retrieved sha256
amesweb-tap-drill AMESweb 2026-10-23 e6501cc1414a
pule-tap-drill CommunityCAD 2026-10-23 625b582c306e
pule-basic-minor CommunityCAD 2026-10-23 00329692204 pule-iso4759-1-nut-height CommunityCAD 2026-10-27 5058ea2d5898
fasten-it-din1587 fasten.it 2026-10-26 27ecd8a57bca
fasteners-eu-din1587 fasteners.eu 2026-10-26 £67e68854e2a schrauben-lexikon-din1587 schrauben -lexikon.de (Wegertseder) 2026-10-26 27cb9268242e fasteners-eu-dini587-drawing fasteners.eu 2026-10-26 beb68a781805 (kept outside the repo)
The whole series (verification map, corrections, drawings): CC-DIN1587-DS.
DIN 1587:2000 - ISO 4759-1 (m min) - ISO 68-1 / ISO 261 (thread) Page 2/2 Acorn nut - M5 - both detail levels - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 82d0e3f1e4052a4ec559d0F9Fd7b4cF7b5772671
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.