'?) CommunityCAD
CC-1S04035-DS-M2.5 revA
Size datasheet - M2.5
ISO 4035 M2.5 hexagon thin nut
Size datasheet: this size's values with their levels, conventions and sources.
mw dw
da
D1
tap
Dimension Thread pitch
Width across flats
Width across corners
Nut height
Wrenching height Bearing face diameter
Countersink diameter
Corner chamfer angle, deg
Countersink angle, deg
Basic minor diameter (crests)
Tap drill (method D - P)
Threaded - M2.5, front view, 6:1
Thread M2.5 x 0.45, ISO metric coarse,
right hand
Part key iso4035-m2-5 Files 2 STEP AP214 (simplified +
threaded)
Value 0.45
4.91 4.82-5.00
25.45
1.475 1.35-1.60
21.10 24.1
2.70 2.50-2.90
22.5 15-30
115 110-120
2.0129 2.05
Level
2 e & L2 La - 2
L1 - 2
Modeled value: nominal, else the midpoint of min-max. < / =: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources. e follows from s and is checked = e min; dw min sets the chamfer's face circle; mw min is checked at mid-flat.
ISO 4035:2012 - ISO 68-1/ ISO 261 (thread)
Hexagon nut - M2.5 - both detail levels - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
Page 1/2
spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205
---
CC-1S04035-DS-M2.5 revA Size datasheet - M2.5
'?) CommunityCAD
Conventions
e Hexagon: regular at the modeled s (the middle of its band), one corner on +X, sharp edges.
« Corner chamfer on both faces: a cone at B (range midpoint) meeting the face on (dw min + s) / 2. Not specified by the standard. « Countersink on both faces at da and 9, both at their range midpoints.
¢ Bore: plain at D (simplified); ISO 68-1 basic internal thread over the full height (threaded), cut by the countersinks.
« No washer face, no markings. Values given only as a limit are modeled at that limit. Features the standard does not dimension are house conventions.
Sources
Source Publisher Retrieved sha256
amesweb-tap-drill AMESweb 2026-10-23 e6501cc1414a
pule-tap-drill CommunityCAD 2026-10-23 625b582c306e
pule-basic-minor CommunityCAD 2026-10-23 00329692204
fasten-it-iso4035 fasten.it 2026-10-25 3849b4c60b37
engineersedge-iso4035 Engineers Edge 2026-10-25 b8755da99aeb
boltport-iso4035 Boltport 2026-10-25 78a545de5f60
iso4035-2012-sample ISO (preview published by iTeh Standards) n/a 6172bfee8723 (kept outside the repo) fuller-iso4035 Fuller Fasteners 2026-10-25 2899f6c7f2b1
The whole series (verification map, corrections, drawings): CC-ISO4035-DS.
ISO 4035:2012 - ISO 68-1/ ISO 261 (thread) Page 2/2 Hexagon nut - M2.5 - both detail levels - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
