m1-z40 Spur Gear, Spur gear datasheet (PDF)

Datasheet — m1-z40 Spur Gear, Spur gear by Milo

Open the PDF
m1-z40 Spur Gear, Spur gearGet the CAD modelm1-z40 Spur Gear, Spur gearCC-SPUR-DS-m1-z40.pdf

Text of this datasheet

'?) CommunityCAD CC-SPUR-DS-m1-240 rev A

Size datasheet - m1-z40

Module 1, 40 teeth, spur gear

Size datasheet: this size's values with their levels, conventions and sources.

SSS For meshing with other module 1 Poh gears on a parallel shaft Part key spur-gears-m1-z40 Pt Files 1 STEP AP214 (simpliieg)

m1-z40, end, 0.5:1 m1-z40, side (the blank), 1:1 (hidden lines dashed)

Dimension

d Reference (pitch) diameter

da Tip (outside) diameter

df Root diameter 37.5% ds Bore diameter (KHK, L2) 10 dh Hub diameter (KHK, L2) 35 b Face width (KHK, L2) 10 th Hub width (KHK, L2) 10 L Total length (KHK, L2) 20 dhH HPC boss (not modeled) 20* dsH HPC bore (not modeled)

a Pressure angle (ISO 53 rack), degrees

ha Addendum (ISO 53 rack), in modules

hf Dedendum (ISO 53 rack), in modules

c Bottom clearance (ISO 53 rack), in modules

p Root fillet radius (ISO 53 rack), in modules

Modeled value: nominal, else the midpoint of min-max. < / =: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources.

ISO 53:1998 (as IS 2535 Part 1:2004); KHK SS table (blank) Page 1/2 Involute spur gear - m1-z40 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec 304229b833a653b73db51178a38d40486ee7c36b

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.

---

. CC-SPUR-DS-m1-z40 revA '?) CommunityCAD Size datasheet - m1-z40

Conventions

¢ Teeth: the ISO 53 basic rack: True involute teeth generated by the standard basic rack rolling on the reference circle: the involute where its straight flank cuts, the fillet its rounded tip cuts and, at small tooth counts, the natural undercut. No profile shift. The rack's values are in the tables (a, ha, hf, c, p; as IS 2535 (Part 1):2004, identical to ISO 53:1998).

« Nominal teeth, no backlash: The tooth is as thick as the space on the reference circle (mm / 2), with no backlash allowance; real gears are cut slightly thinner.

« Modules 0.5 and 0.8: Not in ISO 54 (it starts at 1): JIS B 1701-2 / DIN 780 modules, cut with the same ISO 53 rack, as every maker read does. * The blank: KHK's SS table: No standard covers a stock gear's blank: bore, hub diameter, face width, hub width and total length are KHK's SS steel spur gear table as its maker drawing (L2, one lineage). The smallest tooth counts are KHK's S3 pinion shape, the hub as large as the

teeth. HPC's differing boss and bore are tabulated, not modeled.

* Plain bore: No set screw and no keyway: KHK's tapped and keyway variants are not modeled.

e Chamfers: Illustrative, not dimensioned by any source read: the tooth tips' chamfer at the band's faces (0.15 m), the hub's end chamfer (0.04 dh) and the bore's (0.05 ds). Machined steel.

Sources

Source Publisher Retrieved sha256

is2535-1-2004 Bureau of Indian Standards (scan published 2026-11-08 e35f719619cO (kept outside the repo) by Public.Resource.Org on archive.org)

khk-gtr-involute-profile KHK (Kohara Gear Industry) 2026-11-08 883acc3bbdbc (kept outside the repo)

sdpsi-elements-metric-gear SDP/SI (Stock Drive Products / Sterling 2026-11-08 36082e77e0b6 (kept outside the repo) Instrument; Wayback Machine copy)

khk-ss-spur-gears KHK (Kohara Gear Industry) 2026-11-08 226fe80d3b8 (kept outside the repo)

misumi-eu-gears MISUMI 2026-11-08 4cdf8665312c (kept outside the repo)

hpe-steel-spur-gears HPC Gears (HPC Europe) 2026-11-08 ecc3e6994698 (kept outside the repo)

The whole series (verification map, corrections, drawings): CC-SPUR-DS.

ISO 53:1998 (as IS 2535 Part 1:2004); KHK SS table (blank) Page 2/2 Involute spur gear - m1-z40 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec 304229b833a653b73db51178a38d40486ee7c36b

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.