* CC-BRG-MINI-FL-DS-F687 rev A '?) CommunityCAD Size datasheet - F687
F and MF series F687 flanged miniature ball bearing
Size datasheet: this bearing's values with their levels, conventions and sources, a row per product as sold.
For 7 mm shafts
Part keys bearings - miniature - flanged- £687, bearings- miniature - flanged-f687 -2z
Files 2 STEP AP214 (simplified)
Built from open F687 - 2Z F687ZZ
F6872ZZ, front view, 2.5:1 F687ZZ, view from above, 1.5:1 Sym. Dimension Value Level d Bore diameter, F687 7.000 1-2 D Outside diameter, F687 14.000 1-2 B Width, F687 3.500 l1 +2 r Chamfer dimension r_s min, F687 > 0.150 1-2 D1 Flange diameter, F687 16.000 l1 +2 C1 Flange width, F687 1.000 l1 +2 d Bore diameter, F687ZZ 7.000 1-2 D Outside diameter, F687ZZ 14.000 1-2 B Width, F687ZZ 5.000 1-2 r Chamfer dimension r_s min, F687ZZ 2 0.150 1-2 D1 Flange diameter, F687ZZ 16.000 l1 +2 C1 Flange width, F687ZZ 1.100 l1 +2
Modeled value: nominal, else the midpoint of min-max. =: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources.
No published standard: NSK, MinebeaMitsumi and NTN listings Page 1/2 Flanged miniature ball bearing - F687 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec 70b2bf787ea8F07904ce030af50bcaf231F0c68F
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
---
* CC-BRG-MINI-FL-DS-F687 rev A '?) CommunityCAD Size datasheet - F687
Conventions
e Rings and corners: Bore d, outside diameter D and width B at the nominals of the product's own row; the rings concentric, their faces flush. Ring corners are quarter-rounds of r_s min; the shape isn't specified.
« Ring faces: Each ring's face is (D - d)/8 wide; the annulus between them is the middle half of the radial section.
¢ Shield and seal (2Z, 2RS): A flat annulus recessed r_s min / 2 below the ring faces, the same for both: no groove, snap wire or lip. Each is built from its own row; a 2RS with no sealed row listed takes the shielded row, labelled.
« Open bearing: The annulus recessed B/4 per face, leaving a solid web between the rings. Balls, cage and raceways are not modeled.
« Flange: A plain disc D1 x C1 flush with the flange - side ring face at Z = 0, its outer edges rounded at r_s min; no relief groove, the corner at its root sharp.
« Values: d, D, B, D1 and C1 at their nominals; r at r_s min, the only limit the sources give. * Markings and grades: No markings. Tolerance class, internal clearance and lubricant are not geometry: one model per bearing and product.
Sources Source Publisher Retrieved a256 nsk-miniature-flanged NSK 2026-10-28 bQ556841F716 nmb-miniature-flanged MinebeaMitsumi (NMB) 2026-10-29 325e325FFd26
The whole series (verification map, corrections, drawings): CC- BRG- MINI-FL-DS.
No published standard: NSK, MinebeaMitsumi and NTN listings Page 2/2 Flanged miniature ball bearing - F687 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec 70b2bf787ea8F07904ce030af50bcaf231F0c68F
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.