. CC-BATTHOLDER-DS-mpd-bhsd-1225-sm rev A 0 CommunityCAD Size datasheet - MPD BHSD-1225-SM
CR1225 Battery Holder (Coin Cell Holder), SMT, MPD BHSD-1225-SM
Size datasheet: the MPD BHSD-1225-SM coin cell holder's values from its maker's drawing, with their levels, conventions and sources. Walls, floors, bays, finger windows, the contact housing and the nickel contacts are illustrative (house rules, ADR 0090); the outline, pocket, legs and terminals are the maker's drawing.
Maker part MPD BHSD-1225-SM
Cell CR1225 _ nH [iL Outline 23.37 long, 14.73 wide, 4.83 high (mm) Terminals two SMT tabs on the board Part key battery -holders-mpd-bhsd- : : . . 1225-sm MPD BHSD-1225-SM, from above, 1.5:1 MPD BHSD-1225-SM, side view, 1.5:1 Files 1 STEP AP214 (simplified)
Dimension
Overall length 23.37 w Overall width 14.73 h Overall height 4.83
w2 SMT tab width 3.50
Modeled value: the maker's nominal. L2: the maker's own drawing (ADR 0089). * amber: one source (LO). c: a source value was corrected. Level - independent sources. Only the dimensions this part's drawing gives are listed.
No published standard (each maker's drawing) Page 1/2 Battery holder - MPD BHSD-1225-SM - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec ec102202cfd5583116e22079ef 262796b321054a
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
---
. CC-BATTHOLDER-DS-mpd-bhsd-1225-sm rev A 0 CommunityCAD Size datasheet - MPD BHSD-1225-SM
Conventions
¢ Body: Matte black. Walls 1.0 mm where the drawing gives no pocket, floors 1.0 mm, tray end walls 1.5 mm, a 1.0 mm rib between bays. Finger windows: the top half of the side walls over the middle third of the length.
« Coin contacts: Positive: a 0.3 mm nickel strip a quarter of the pocket wide from the housing to the pocket's centre, resting on the seated cell's positive face (owner #1038 B), on a post down to its pin or tab. Negative: a 0.3 mm disc half the pocket across on the floor.
¢ Tray contacts: Negative: a coil of five 0.5 mm rings 1.0 mm apart on a base plate. Positive: a 0.3 mm plate with a centre dimple. Cells wired in series; the terminals as the maker's drawing places them.
¢ Terminals: Pins 0.8 x 0.5 mm, 3.0 mm long where the drawing gives no section or length; SMT tabs 0.3 mm on the board, a quarter of the pocket wide where no w2.
e Mark: The CommunityCAD mark recessed 0.3 mm into the underside at the centre, a quarter of the smaller plan side. « Values: Every dimension is the maker's own drawing of that part (L2, one lineage, ADR 0089), at its nominal.
Sources Source Publisher Retrieved sha256 mpd-holders Memory Protection Devices, Inc. 2026-10-29 bfb9434db311 (kept outside the repo)
The whole series (verification map, corrections, drawings): CC- BATTHOLDER-DS.
No published standard (each maker's drawing) Page 2/2 Battery holder - MPD BHSD-1225-SM - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec ec102202cfd5583116e22079ef 262796b321054a
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.