'?) CommunityCAD
CC-DCBLOWER-DS-9733 revA Size datasheet - 9733
9733 DC radial blower
Size datasheet: this blower's values with their levels, conventions and sources. Housing curve, ears, outlet opening and impeller are illustrative, not any maker's design; overall size, axis position
and mounting holes are from maker drawings.
9733, inlet face, 0.2:1 9733, side view, 0.4:1 Sym. Dimension a Overall length b Overall width t Thickness xo Axis to outlet face yo Axis to straight wall x1 Hole 1 along, from the axis yl Hole 1 across, from the axis x2 Hole 2 along, from the axis y2 Hole 2 across, from the axis dh Hole diameter
Envelope
Mounting holes
Part key
Files
97.2 x 94.4 x 33mm
2 x #4.5 through t, diagonally opposite (positions from the axis: table)
fans - blower-9733 1 STEP AP214 (simplified)
Value Level 97.2 Li - 3 94.4 1-3 33.0 Li - 3 50.0 ll: 3 51.9c ll - 2 39.0 1-3 39.0 L1- 2 32.0 ll - 2 32.0 Li - 3 4.5 1-3
Modeled value: the nominal. * amber: one source (LO). c: a source value was corrected. Level - independent sources.
No published standard (makers' drawings) DC radial blower - 9733 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
Page 1/2
spec aéebc7dae7b620Fd2487b4d313F49ae74ad0d1F4
---
* CC-DCBLOWER-DS-9733 revA '?) CommunityCAD Size datasheet - 9733
Conventions
Illustrative housing: A spiral volute about the axis, its radius changing evenly between the sourced extremes (yo, a - xo, b - yo); the duct from the outlet face back to the axis; each hole in an ear 2-dh wide; all clipped to a x b.
« Walls and outlet: Walls t/12 everywhere, the four sides of the outlet opening too; the opening is what remains. Outlet opening is illustrative; check the maker's drawing before designing a duct.
e Inlet and impeller: Inlet 1.2 x min(a - xo, yo) on the axis until the makers' inlet diameter is in the data (#1025). Forward-curved blades (one per mm of inlet, 30 to 48), a back plate, a front ring and a hub of half the inlet with the CommunityCAD mark, light grey.
« Holes, edges, leads: Two plain through holes dh, diagonally opposite: hole 1 at x1, y1 from the axis on the straight-wall side, hole 2 at x2, y2 on the outlet side. Sharp edges; no labels, moulded arrows or lead wires.
¢ Values: a, b, t, xo, yo, x1, y1, x2, y2 and dh at their reconciled values from two or more makers' drawings (no published standard); within the makers' tolerance the most precise, then the lowest.
Sources
Source Publisher Retrieved sha256
sunon-dc-blower-255e Sunon 2026-10-26 Sa8f0Fffc83db (kept outside the repo) mechatronics-dc-blower Mechatronics Fan Group 2026-10-28 Sd88ba9a3sefF (kept outside the repo) delta-dc-blower Delta Electronics, Inc. 2026-10-28 Occ39ec2947b (kept outside the repo)
The whole series (verification map, corrections, drawings): CC- DCBLOWER-DS.
No published standard (makers' drawings) Page 2/2 DC radial blower - 9733 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec aéebc7dae7b620Fd2487b4d313F49ae74ad0d1F4
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.