'?) CommunityCAD CC-N20-DS-9 revA
Size datasheet - 9
N20 gearmotor, 9 mm gearbox
Size datasheet: this size's values with their levels, conventions and sources.
For N20 motor mounts, clamps and enclosures
Part keys gearmotors-n20-9 and gearmotors-n20-9-ext
Files 2 STEP AP214 (simplified),
plain and extended rear shaft
9, front face, 2:1 9, side, 0.5:1 (hidden lines dashed) Sym. Dimension Value Level Lg Gearbox length 9 La - 4 Ww Gearbox width 12 L1-4 H Gearbox height 10 L1-4 Lm Motor can length 15.1 L1-4 Dm Motor can width 12 L1-4 OL Overall length (Pololu) < 25.6* lo. 1 E Shaft length from the face 10 L1- 3 d Shaft diameter 3 L1-4 f Shaft across the flat 2.5 L1- 3 B Front boss diameter 4 L1-4 h Front boss height 0.8 L1-4 n Number of mounting holes Q La - 4 M Mounting hole thread 1.6 La - 4 A Mounting hole spacing 9 Li - 3 e Hole offset (Pololu, checked) 4.5% lo. 1 Br Rear boss diameter 5 L1- 3 hr Rear end height 1.2 Li - 3 pt Terminal spacing 6.9% lo. 1 dr Rear shaft diameter (ext) 1.0* lo -1 Lr Rear shaft length (ext) 5x Lo - 1
Modeled value: nominal, else the midpoint of min-max. s / =: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources.
Makers' drawings: Pololu, TT Motor, Motraxx, GA12-N20 (no published standard) Page 1/2 N20 micro metal gearmotor - 9 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec ca98d3531843b0ccc0fb3c4381b92670a1b41e89
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
---
CC-N20-DS-9 revA Size datasheet - 9
'?) CommunityCAD
Conventions
+ Where makers differ: The largest stated gearbox length, can length, shaft length and bosses, so a mount or enclosure made to the model clears every maker's motor; the shaft and its flat are exact. Each maker's value is on the page. Motraxx's longer can is drawn on a 9 mm box only, so the 12.5 mm box's can is the other makers' (#1372, left at the defaults; each size's page gives both lengths).
« Gearbox and gears: Brass-coloured front, middle and rear plates with rounded corners on four corner spacers, the tapped holes in sleeves behind the front plate, two flush cross-head screws in the face's corners, and an untoothed steel gear stack in the gaps. Illustrative, not any maker's design, checked for fit only.
« Can, end cap and terminals: The can's flats at the gearbox's height, two slots in each flat; a black nylon end cap carrying the rear boss; two tinned solder tabs at the terminal spacing, a red polarity dot beside the + tab and the CommunityCAD mark in the end cap. Illustrative.
e Holes and shaft: Tapped holes as plain bores at the thread's nominal diameter, 1.5 x that deep; the D flat over most of the shaft past the boss; chamfers on the shaft's end and the boss's edge. Illustrative.
« Motor can length Lm: the makers differ (the GA12-N20 sheet 15 mm, Motraxx 15.1 mm, Pololu 15 mm, TT Motor 15 mm). The model uses the largest stated, 15.1 mm, so a mount or enclosure made to it clears every maker's motor.
« Front boss height h: the makers differ (the GA12-N20 sheet 0.7 mm, Motraxx 0.7 mm, Pololu 0.7 mm, TT Motor 0.8 mm). The model uses the largest stated, 0.8 mm, so a mount or enclosure made to it clears every maker's motor.
« This size's can is 15.1 mm. Motraxx's 15.1 mm can is drawn on its 9 mm box only, so the 12.5 mm box's can is 15 mm, though the motor behind both boxes is the same. Left at the defaults of the open decision (#1372); check your own motor's can if it matters.
Sources
Source Publisher Retrieved sha256
pololu-micro-metal-gearmotors Pololu 2026-11-05 d2b24afa17b1 ttmotor-gm12-n20va Shenzhen TT Motor 2026-11-07 1e96624ccd45 handsontec-ga12-n20 Handson Technology 2026-11-07 3ef4b636eF45 ttmotor-gm12-n20va-figures Shenzhen TT Motor 2026-11-07 1e96624ccd45 motraxx-gm12f-n20vs-298-figures Motraxx Elektrogeraete GmbH (Conrad copy) 2026-11-07 e55c2ee580b6 handsontec-ga12-n20-figures Handson Technology 2026-11-07 3ef4b636eF45
The whole series (verification map, corrections, drawings): CC-N20-Ds.
Makers' drawings: Pololu, TT Motor, Motraxx, GA12-N20 (no published standard) Page 2/2 N20 micro metal gearmotor - 9 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec ca98d3531843b0ccc0fb3c4381b92670a1b41e89
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.