40 I-type slot 8 large Extrusion Corner Bracket datasheet (PDF)

Datasheet — 40 I-type slot 8 large Extrusion Corner Bracket by Milo

Open the PDF
40 I-type slot 8 large Extrusion Corner BracketGet the CAD model40 I-type slot 8 large Extrusion Corner BracketCC-CORNBRKT-DS-i8-large.pdf

Text of this datasheet

'?) CommunityCAD CC-CORNBRKT-DS-i8-large rev A

Size datasheet - i8-large

AO I-type slot 8 large corner bracket

Size datasheet: this size's values with their levels, conventions and sources.

_— |

For 40 I-type slot 8 aluminium H extrusions | H Part key extrusion-corner-brackets-i8- ' large | rrr—Cs—CsY | Files 1 STEP AP214 (simplified) \ i8-large, face, 0.5:1 i8-large, side, 0.5:1 (hidden lines dashed) Sym. Dimension Value Level L Leg length 80* Lo-1 h Upright leg length 80x* lo-41 w Width 4Ox Lo-1 ey Hole column from the side 20* LO: 1 ee Hole to leg end 20* Lo-1 px Hole spacing along a leg 4Ox Lo-1

Modeled value: nominal, else the midpoint of min-max. < / 2: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources.

No published standard (makers' drawings) Page 1/2 Extrusion corner bracket - i8-large - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec 304229b833a653b73db51178a38d40486ee7c36b

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.

---

'?) CommunityCAD CC-CORNBRKT-DS-i8-large rev A

Size datasheet - i8-large

Conventions

« Casting: Side walls of the wall thickness, an inside fillet, key width and length and, on the slot 10 and 45 brackets, a curved diagonal: illustrative, not any maker's design.

« Mark: The CommunityCAD mark recessed 0.3 mm in an outside side wall. Illustrative.

« Values: No published standard: every maker casts its own bracket, so each size is the reference maker's own casting (Misumi, OpenBuilds, item), single source. item's sheets give only the outline and holes: its wall and key are house proportions, its hole ISO 273 medium for M8. On the 20 B-type slot 6 double, Misumi's drawing alone shows which holes sit on its rows. The two readings disagreed, and the owner accepted this layout: 4 holes on the first leg in two rows, 2 on the upright in one, no centre column.

« \V-slot holes: OpenBuilds' drawing gives the holes of the 20 V-slot bracket no position, so they sit at the middle of the leg and of the width, a rule rather than a maker's dimension.

¢ Finish: Cast aluminium, the reference part's finish: render and metadata only. First leg's profile face at Z = 0, the upright's at X = 0, the keys beyond them.

Sources Source Publisher Retrieved sha256 item-angle-brackets item Industrietechnik GmbH 2026-10-30 O5e0df30157e (kept outside the repo)

The whole series (verification map, corrections, drawings): CC-CORNBRKT-DS.

No published standard (makers' drawings) Page 2/2 Extrusion corner bracket - i8-large - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec 304229b833a653b73db51178a38d40486ee7c36b

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.