CC-DIN705-DS-4 revA Size datasheet - 4
'?) CommunityCAD
DIN 705 4 shaft collar
Size datasheet: this size's values with their levels, conventions and sources, for forms A and B.
Fits a 4mm shaft Part keys din705-a-d4, din705-b-d4 ) Files 3 STEP AP214: form A simplified and threaded, form B simplified 4 form A, front view, 4:1 4 form A, view from above, 3:1 Sym. Dimension Value Level di Bore, H8 (band middle) 4.009 L1- 2 4-4.018 d2 Outside, h13 (band middle) 7.89 L1-3 7.78-8 b Width, js14 5 L1- 3 ic Outside chamfer, 0.1 b 0.5 - d3 Set-screw thread, form A 2.5 L1- 3 ls Set-screw length, form A 3) La - 2 d4 Pin hole, form B 1 L1 + 2
Modeled value: d1 and d2 at the middle of their ISO 286-2 band (grey: its limits), the rest at their nominals. * amber: one source (LO). c: a source value was corrected. Level - independent sources.
DIN 705:2019-03 (as tabulated) - ISO 286-2 (H8, h13) Page 1/2 Shaft collar - 4 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec 946d39588085996aee8F621a618103eb3a8F37bd
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
---
CC-DIN705-DS-4 revA Size datasheet - 4
'?) CommunityCAD
Conventions
e Outside chamfer: One chamfer of 0.1 b x 45 degrees on the +Z face's outside edge, drawn about that size by the standard, not dimensioned. Both bore edges and the other outside edge sharp; small breaks seen on real parts aren't modeled.
« Set-screw hole, form A: Radial on +X at b/2, through the wall into the bore, with a sharp mouth; the countersink seen on real parts isn't modeled. Simplified level: a plain cylinder at the nominal d3. Threaded level: ISO 68-1 basic internal profile, right hand, coarse pitch, over the full wall.
« Set screw, form A: Not modeled: the collar only. The standard's screw is slotted, ISO 7434, d3 x I_s; hex socket screws (ISO 4026-4029) are common in trade.
« Pin hole, form B: A straight d4 hole on +X at b/2, through the near wall only. Reamed 1:50 together with the shaft at assembly. Form B starts at di=4.
e Values: d1 at the middle of its H8 band and d2 at the middle of its h13 band, both wholly off the nominal; b, d3 and d4 at their nominals.
« Walls, markings and finish: Concentric bore and outside, flat parallel faces; their tolerances aren't modeled. No markings. Material and finish are metadata only: one model per form and size.
Sources
Source Publisher Retrieved sha256
is1367-2-2002 Bureau of Indian Standards (scan 2026-10-27 970774660c5e (kept outside the repo) published by Public.Resource.Org on archive.org)
engineersedge-iso286-shafts Engineers Edge 2026-10-25 9799d88b4078
bossard-iso286-2-tolerances Bossard 2026-10-30 e872fdb362e6 (kept outside the repo)
fasten-it-din705 fasten.it 2026-10-30 4be2fc7e2492
fasten-it-din705-b fasten.it 2026-10-30 9cd098aa1d54
dinmark-din705 Dinmark (Ukraine) 2026-10-30 84a1c5f3a868
dinmark-din705-b Dinmark (Ukraine) 2026-10-30 3143f68daf7F
maedler-din705 Madler GmbH 2026-10-30 793a2d93da4t
The whole series (verification map, corrections, drawings): CC-DIN705-Ds.
DIN 705:2019-03 (as tabulated) - ISO 286-2 (H8, h13) Page 2/2 Shaft collar - 4 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec 946d39588085996aee8F621a618103eb3a8F37bd
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.