3/8-16 Tripod Reducer Bushing, ISO 1222 datasheet (PDF)

Datasheet — 3/8-16 Tripod Reducer Bushing, ISO 1222 by Milo

Open the PDF
3/8-16 Tripod Reducer Bushing, ISO 1222Get the CAD model3/8-16 Tripod Reducer Bushing, ISO 1222CC-ISO1222B-DS-3-8-16.pdf

Text of this datasheet

CC-1S01222B-DS-3-8-16 revA Size datasheet - 3/8-16 x 1/4-20

'?) CommunityCAD

ISO 1222 3/8-16 x 1/4-20 reducer bushing

Size datasheet: this size's values with their levels, conventions and sources.

Part key iso1222-b-3-8-16 Files 1 STEP AP214 (simplified)

3/8-16 x 1/4-20, front view, 3:1 3/8-16 x 1/4-20, view from above, 3:1

Dimension Level

P Outside pitch, 3/8-16 1.588 L2

d Outside major diameter (Table 2, 3/8-16) 9.312 9.132-9.492

o al di Outside minor diameter (Table 2, 3/8-16) 7.806 H Length = 3/8-16 hole depth h (Fig. 1 a) 2 5.5* lo-41 z End chamfer length (Fig. 1b) < 1.3* lo- 41 Pi Inside pitch, 1/4-20 1.270 pe | D Inside major diameter (Table 1, 1/4-20) 6.350 D1 Inside minor diameter (Table 1, 1/4-20) 4.975 t 1/4-20 full-thread depth (Fig. 1a) > 4x lo-4 e Mouth countersink depth (Fig. 1 a) < 1*x lo-4 dc Countersink at the face (90°, house) 6.975 house n Slot width (0.16 d, house) 1.49 house m Slot depth (H / 4, house) 1.375 house

Modeled value: nominal, else the midpoint of min-max. < / 2: only that limit is given, modeled at it. * amber: one source (LO). house: a stated house rule. Level - independent sources.

ISO 1222:2010 Page 1/2 Reducer bushing - 3/8-16 x 1/4-20 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.

---

CC-1S01222B-DS-3-8-16 revA Size datasheet - 3/8-16 x 1/4-20

'?) CommunityCAD

Conventions

e Edition and threads: ISO 1222:2010 from its complete free preview (ADR 0059): the 3/8-16 bolt thread outside (Table 2) and the 1/4-20 nut thread inside (Table 1), at their band midpoints (else the basic). Simplified level: a plain cylinder at d and a plain bore at D1.

« Length and bore: The length is the 3/8-16 socket's hole depth h, so the bushing fills a Figure 1 socket; the 1/4-20 thread runs through it, which holds the 1/4-20 thread depth t and hole depth h.

e Ends: The lower outside end chamfered from d to d1 over z, as the bolt end, its end face at Table 2's d1 max (basic + es), not the basic in the table. The 1/4-20 mouth countersunk 90° included to the depth e, at Figure 1's limit. The bore's lower edge sharp.

« Slot, markings, material: A straight screwdriver slot along X, 0.16 d wide and a quarter of the length deep. No markings. Brass: render material only.

Sources Source Publisher Retrieved sha256 iso1222-2010-sample ISO (preview published by iTeh Standards) 2026-10-31 ad728f67a8e8 (kept outside the repo)

iso1222-2010-sample-figures ISO (preview published by iTeh Standards) 2026-10-31 ad728f67a8e8 (kept outside the repo)

The whole series (verification map, drawings): CC-ISO1222B-DS.

ISO 1222:2010 Page 2/2 Reducer bushing - 3/8-16 x 1/4-20 - Dimensions in mm - CC-BY 4.0, IronPixel Labs LLC spec cfd05b053c736a4f15ba3030aa41f ebd40cdc205

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.