CC-1S801222-DS-3-8-16 revA Size datasheet - 3/8-16
'?) CommunityCAD
ISO 1222 3/8-16 camera screw
Size datasheet: this size's values with their levels, conventions and sources.
Part key iso1222-3-8-16x10 Files 2 STEP AP214 (simplified + threaded)
3/8-16, front view, 1.5:1 3/8-16, view from above, 1.5:1
Dimension Level
P Pitch (25.4 / tpi) 1.588 2-4
d Thread major diameter (Table 2) 9.312 [ee 9.132-9.492
d2 Thread pitch diameter (Table 2) 8.378 [ee 8.295-8.461
di Thread minor diameter (Table 2) 7.806
L Protrusion from the bearing face (Fig. 1 b) 4.5% lo-1
b Thread length from the end (Fig. 1 b) > 3.5% lo- 1
z End chamfer length (Fig. 1 b) < 1.3* lo- 1
dr Bearing face recess limit (clause 4) < 20
dk Head diameter (2.2 d, house) 20.486 house
k Head height (0.6 d, house) 5.587 house
n Slot width (0.16 d, house) 1.49 house
s Hex socket across flats (0.5 d, house) 4.656 house
dn Captive neck (0.9 d1, house) 6.79 house
w D-ring wire (0.12 d, house) 1.117 house
Modeled value: nominal, else the midpoint of min-max. s / =: only that limit is given, modeled at it. * amber: one source (LO). house: a stated house rule. Level - independent sources.
ISO 1222:2010 Page 1/2 Camera screw - 3/8-16 - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 946d39588085996aee8F621a618103eb3a8F37bd
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
---
. CC-1S801222-DS-3-8-16 revA '?) CommunityCAD Size datasheet - 3/8-16
Lengths L Basis Makers state Makers Part key 10 house length (owner, #438) 10, 9.525 2 iso1222-3-8-16x10
Under-head length 10 mm: ISO 1222 gives none, so this library's house length is the whole millimetre the makers' own stated lengths round to (Kupo 10 mm, Really Right Stuff 9.525 mm). They agree near it, not exactly.
Conventions
« Edition and threads: ISO 1222:2010 from its complete free preview (ADR 0059). The threads are the standard's own Tables 1 and 2, not UNC 1A/1B, at their band midpoints (else the basic). Simplified level: the thread a plain cylinder at d.
e Thread end (Figure 1 b): The thread runs b from the end face, the chamfer included; the end is chamfered from d to an end face of d1 over z. b and zare single limits, modeled at the limit. Above the thread the shank is the plain neck.
« Head, slot and hex socket: Round head 2.2 d across and 0.6 d high, its top edge rounded 0.15 k; a straight slot 0.16 d wide and k/2 deep along X; a hex socket 0.5 d across flats in the slot's centre, a corner on +X, its floor k/4 below the slot floor.
« D-ring and captive neck: A fold- down D-ring of 0.12 d wire, folded flat on the head over -X, a second solid; its pivot is not modeled. A plain neck of 0.9 d1 under the head keeps the screw captive in a plate's tapped hole.
« Lengths, markings, material: One under-head length L per size, a house length the owner chose (#438): ISO 1222 gives none, so L is the whole mm every maker's stated length rounds to (Kupo, Really Right Stuff): near agreement, not one maker's exact figure. No markings. Stainless steel, chrome-plated ring: render material only.
Sources
Source Publisher Retrieved sha256
iso1222-2010-sample ISO (preview published by iTeh 2026-10-31 ad728f67a8e8 (kept outside the repo) Standards)
iso1222-2010-sample-figures ISO (preview published by iTeh 2026-10-31 ad728f67a8e8 (kept outside the repo) Standards)
mediagear-kupo-pan-head-screws MediaGear (Kupo dealer, Estonia) 2026-11-05 1d270ad65b36
rprs-camera-screws Really Right Stuff 2026-11-05 584a68cb6396
rule-iso1222-Length CommunityCAD 2026-11-05 9%bd87c143d08
The whole series (verification map, drawings): CC-ISO1222-Ds.
ISO 1222:2010 Page 2/2 Camera screw - 3/8-16 - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 946d39588085996aee8F621a618103eb3a8F37bd
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.