30 B-type slot 8 M4 Hammer-head T-slot Nut datasheet (PDF)

Datasheet — 30 B-type slot 8 M4 Hammer-head T-slot Nut by Milo

Open the PDF
30 B-type slot 8 M4 Hammer-head T-slot NutGet the CAD model30 B-type slot 8 M4 Hammer-head T-slot NutCC-TNUTH-DS-b8-M4.pdf

Text of this datasheet

CC-TNUTH-DS-b8-M4 revA Size datasheet - b8-M4

'?) CommunityCAD

30 B-type slot 8 M4 hammer-head T-slot nut

Size datasheet: this size's values with their levels, conventions and sources.

For 30 B-type slot 8 aluminium extrusions [ Part key slot-nuts-hammer-b8-m4 Files 2 STEP AP214 (simplified, threaded) b8-M4, top, 2.5:1 b8-M4, end, 2.5:1 (hidden lines dashed) Sym. Dimension Value Level Ww Body width across the slot 15 L1- 2 L Body length along the slot 8 L1- 2 b Neck width 7.8 L1- 2 h Overall height 6.3 L1- 2 k Body height 5.5 L1- 2 n Neck height 0.8 L1- 2

Modeled value: nominal, else the midpoint of min-max. < / 2: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources.

No published standard (makers' drawings) Page 1/2 Hammer-head T-slot nut - b8-M4 - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 304229b833a653b73db51178a38d40486ee7c36b

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.

---

* CC-TNUTH-DS-b8-M4 revA '?) CommunityCAD Size datasheet - b8-M4

Conventions

« Rounded corners and flanks: Two diagonal corners rounded to the width's arc, so the nut turns within its length, and the body's lower edges chamfered 45 degrees by k/2. Both illustrative, not any maker's dimensions.

« Values: No published standard: each value the reference maker's drawing (Misumi). A second maker's value counts as agreeing where the slot leaves room for the difference, computed from the profile's data, and a size where a value stands on one maker is labelled single source.

¢ Fit: A nut is checked against its slot system's one-cell profile, never fitted to it: neck no wider than the opening, width no wider than the undercut, body no taller than the cavity.

« Finish: Brushed stainless: render and metadata only. No markings, no serrations, other edges sharp. Bottom face at Z = 0, the neck toward +Z.

Sources

Source Publisher Retrieved sha256

misumi-hammer-nuts MISUMI 2026-10-30 ef5782b7977a (kept outside the repo) motedis-hammer-nuts Motedis 2026-10-30 e86e703313ed (kept outside the repo) rule-motedis-hammer-nut-heights CommunityCAD 2026-10-31 87e163a9a166 rule-misumi-hammer-nut-neck CommunityCAD 2026-11-03 d573#37888b3

The whole series (verification map, corrections, drawings): CC-TNUTH-DS.

No published standard (makers' drawings) Page 2/2 Hammer-head T-slot nut - b8-M4 - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 304229b833a653b73db51178a38d40486ee7c36b

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.