14x27 Stepper Motor, NEMA ICS 16 datasheet (PDF)

Datasheet — 14x27 Stepper Motor, NEMA ICS 16 by Milo

Open the PDF
14x27 Stepper Motor, NEMA ICS 16Get the CAD model14x27 Stepper Motor, NEMA ICS 16CC-NEMA-DS-14x27.pdf

Text of this datasheet

CC-NEMA-DS-14x27 revA Size datasheet - 14x27

'?) CommunityCAD

NEMA 14 stepper motor, 27 mm body

Size datasheet: this size's values with their levels, conventions and sources.

For NEMA 14 motor mounts and brackets Part key nema-steppers-14x27 Files 1 STEP AP214 (simplified) 14x27, mounting face, 0.5:1 14x27, side, 0.5:1 (hidden lines dashed)

Sym. Dimension Value Level L Body length (house) 27x lo -1 BD Body square < 35.3 L1- 2 A Mounting hole spacing 26 Lia - 2 n Number of mounting holes 4 Lia - 2 M Tapped hole thread 3 L1 + 2 N Pilot diameter 22 L1- 2 T Pilot height 2 Lia - 2 D Shaft diameter 5 L1- 2 E Shaft length from the mounting face 24 L1-2 F Across the shaft's flat 4.5 L1- 2 Lf Flat length 15* Lo -1

Modeled value: nominal, else the midpoint of min-max. < / 2: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources.

NEMA ICS 16 Table 4 (frames 17, 23, 34) and makers' drawings Page 1/2 NEMA hybrid stepper motor - 14x27 - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 304229b833a653b73db51178a38d40486ee7c36b

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.

---

CC-NEMA-DS-14x27 revA Size datasheet - 14x27

'?) CommunityCAD

Conventions

* Body length: One house length per size: the whole mm the makers' stated lengths round to, the most makers' within 2 mm, the longer on a tie. Backed by the makers listed on each page; no one maker's value.

* Where makers differ: The largest stated square, pilot height, shaft length and through hole, so a bracket made to the model clears every maker's motor; each maker's value is on the page.

e Body and caps: Three solids: black end caps and the silver laminated stack, their corners cut, a seam at each end of the stack; on frames 23 and 34 a thinner front flange and the body's corners cut back clear of the through holes. Illustrative, not any maker's design, checked for fit only.

e Holes, shaft and rear: Tapped holes as plain bores at the thread's nominal diameter, 1.5 x that deep; the shaft's end chamfered; a shallow round recess in the rear face; a 4-way connector in one side of the rear cap; a label with the CommunityCAD mark. Illustrative.

¢ Body length 27 mm is a house length (#1227 item 2 A): the whole mm the makers' stated lengths round to. lin-3518x-08: 26; moons-hybrid- steppers: 27.3.

Sources

Source Publisher Retrieved sha256

‘Leadshine-cm-steppers Leadshine Technology (copy 2026-11-06 efe3aeb429Fa distributed by MAS Auto Systems)

leadshine-cm-steppers-figures Leadshine Technology (copy 2026-11-06 efe3aeb429Fa distributed by MAS Auto Systems)

moons-hybrid-steppers MOONS' Industries (copy hosted by 2026-11-06 378b261822d8 (kept outside the repo) MEV Elektronik)

pule-nema-steppers-length CommunityCAD 2026-11-06 f9a30cef3bb8

The whole series (verification map, corrections, drawings): CC-NEMA-DS.

NEMA ICS 16 Table 4 (frames 17, 23, 34) and makers' drawings Page 2/2 NEMA hybrid stepper motor - 14x27 - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 304229b833a653b73db51178a38d40486ee7c36b

Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.