CC-NEMA-DS-11x32 rev A Size datasheet - 11x32
'?) CommunityCAD
NEMA 11 stepper motor, 32 mm body
Size datasheet: this size's values with their levels, conventions and sources.
For NEMA 11 motor mounts and brackets Part key nema-steppers- 11x32 Files 1 STEP AP214 (simplified) 11x32, mounting face, 0.75:1 11x32, side, 0.5:1 (hidden lines dashed) Sym. Dimensi Value Level L Body length (house) 32x lo - 1 BD Body square < 28.3 L1 - 3 A Mounting hole spacing 23 L1- 3 n Number of mounting holes 4 L1- 3 M Tapped hole thread 2.5 L1- 3 N Pilot diameter 22 L1 - 3 T Pilot height 2 L1- 3 D Shaft diameter 5 L1 - 3 E Shaft length from the mounting face 24 L1- 3 F Across the shaft's flat 4.5 L1 - 3 Lf Flat length 15 L1- 3
Modeled value: nominal, else the midpoint of min-max. s / =: only that limit is given. * amber: one source (LO). c: a source value was corrected. Level - independent sources.
NEMA ICS 16 Table 4 (frames 17, 23, 34) and makers' drawings Page 1/2 NEMA hybrid stepper motor - 11x32 - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 02F48ec29f9e7bFFOeF756F4F5d939300beee1e6
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.
---
* CC-NEMA-DS-11x32 rev A '?) CommunityCAD Size datasheet - 11x32
Conventions
* Body length: One house length per size: the whole mm the makers' stated lengths round to, the most makers' within 2 mm, the longer on a tie. Backed by the makers listed on each page; no one maker's value.
« Where makers differ: The largest stated square, pilot height, shaft length and through hole, so a bracket made to the model clears every maker's motor; each maker's value is on the page.
e Body and caps: Three solids: black end caps and the silver laminated stack, their corners cut, a seam at each end of the stack; on frames 23 and 34 a thinner front flange and the body's corners cut back clear of the through holes. Illustrative, not any maker's design, checked for fit only.
e Holes, shaft and rear: Tapped holes as plain bores at the thread's nominal diameter, 1.5 x that deep; the shaft's end chamfered; a shallow round recess in the rear face; a 4- way connector in one side of the rear cap; a label with the CommunityCAD mark. Illustrative.
« Body length 32 mm is a house length (#1227 item 2 A): the whole mm the makers' stated lengths round to. leadshine-cm- steppers: 32; lin- 211-13-01: 32; moons-hybrid- steppers: 32.
Sources
Source Publisher Retrieved sha256
‘Leadshine-cm-steppers Leadshine Technology (copy 2026-11-06 efe3aeb429Fa distributed by MAS Auto Systems)
leadshine-cm-steppers-figures Leadshine Technology (copy 2026-11-06 efe3aeb429Fa distributed by MAS Auto Systems)
moons-hybrid-steppers-figures MOONS' Industries (copy hosted by 2026-11-06 378b261822d8 (kept outside the repo) MEV Elektronik)
orientalmotor-pkp22-drawing Oriental Motor 2026-11-06 2c47c6060434
rpule-nema-steppers-length CommunityCAD 2026-11-06 f9a30cef3bb8
The whole series (verification map, corrections, drawings): CC- NEMA-DS.
NEMA ICS 16 Table 4 (frames 17, 23, 34) and makers' drawings Page 2/2 NEMA hybrid stepper motor - 11x32 - Dimensions in mm - CC-BY 4.0, lronPixel Labs LLC spec 02F48ec29f9e7bFFOeF756F4F5d939300beee1e6
Modeled from cited sources; not certified. Found an error? Use the feedback section on the part page.